manualshive.com logo in svg

Paradyne FrameSaver SLV 9664, Руководство пользователя

Построенный на инновационной технологии Paradyne FrameSaver SLV 9664 обеспечивает надежную защиту вашего устройства. Для получения подробной информации об использовании рекомендуется скачать бесплатное руководство пользователя с нашего веб-сайта. Не упустите возможность загрузить его сейчас с manualshive.com.

Поделиться
Скачать
background image

Troubleshooting

 6-18

9664-A2-GB20-00

March 2000

IP Ping Test

An IP Ping test can be run to test connectivity between the FrameSaver unit and
any FrameSaver device, router, or NMS to which it has a route.

Times when you might want to run an IP Ping test are:

H

To test connectivity between the FrameSaver unit and any FrameSaver
device in the network to verify that the path is operational. Select Procedure 1
to Ping any far-end FrameSaver device.

H

To verify the entire path between a newly installed remote site FrameSaver
device and the central site NMS. During a remote site installation, an IP Ping
test is typically run from the remote site to Ping the NMS at the central site.
The remote FrameSaver device must have SNMP trap managers configured,
and one of those trap managers must be the central site NMS. Select

Procedure 2

 to Ping the NMS at the central site.

H

To test the path to the NMS trap managers during installation of the central
site FrameSaver unit. The remote FrameSaver device must have configured
the SNMP trap managers to be sent the Ping. Select 

Procedure 2

 to Ping the

SNMP trap managers.

"

Procedure 1

To Ping any far-end FrameSaver device:

1. Select the IP Ping test.

Main Menu

→

Test

→

IP Ping

2. Enter the IP Address of the device the Ping is being sent to, then select Start.

NOTE:

If the FrameSaver unit has just initialized, or the far-end device has just
initialized, it may take about a minute for the devices to learn the routes
via the proprietary RIP.

3. Verify the results of the IP Ping test.

— While the test is running, 

In Progress...

  is displayed in the Status

field.

— When the test is finished, 

Alive. Latency = 

nn

 ms

 should appear

as the Status (

nn being the amount of time the test took in milliseconds).

If any other message is displayed, additional testing will be required.

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

H3C MSR 20-20 Supplementary Manual preview
MSR 20-20
Бренд: H3C Страницы: 6
3Com OfficeConnect 3CP4144 How To Set Up preview
OfficeConnect 3CP4144
Бренд: 3Com Страницы: 4
3Com OfficeConnect 3CP4144 Release Note preview
OfficeConnect 3CP4144
Бренд: 3Com Страницы: 2
H3C MSR 20-20 User Manual preview
MSR 20-20
Бренд: H3C Страницы: 60
H3C MSR 20 Series Manual preview
MSR 20 Series
Бренд: H3C Страницы: 149
3Com 3C13636 Installation Manual preview
3C13636
Бренд: 3Com Страницы: 27
3Com OfficeConnect 3C19500 User Manual preview
OfficeConnect 3C19500
Бренд: 3Com Страницы: 52
M2M Pro User Manual (Extract preview
Pro
Бренд: M2M Страницы: 9
Idis DR-8416 Operation Manual preview
DR-8416
Бренд: Idis Страницы: 123
Idis DR-6232H Installation Manual preview
DR-6232H
Бренд: Idis Страницы: 29
Idis DR-4516P Installation Manual preview
DR-4516P
Бренд: Idis Страницы: 28
Idis DirectIP DR-1304P Operation Manual preview
DirectIP DR-1304P
Бренд: Idis Страницы: 82
iDirect Evolution X1 Installation Manual preview
Evolution X1
Бренд: iDirect Страницы: 130
IBM 8677 - BladeCenter Rack-mountable - Power... Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power...
Бренд: IBM Страницы: 126
LaCie 301160U - 1TB Ethernet Disk RAID Network Attached... Quick Install Manual preview
301160U - 1TB Ethernet Disk RAID Network Attached...
Бренд: LaCie Страницы: 5
Vonets MINI300 Quick Setting Manual preview
MINI300
Бренд: Vonets Страницы: 8
Lorex LNR100 SERIES Instruction Manual preview
LNR100 SERIES
Бренд: Lorex Страницы: 186
LaCie 5BIG NAS PRO Quick Install Manual preview
5BIG NAS PRO
Бренд: LaCie Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды