Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 100

Страница: 100 / 240

Operation and Maintenance

5-6

9664-A2-GB20-00

March 2000

Device Messages

These messages appear in the messages area at the bottom of the screens.
All device messages are listed in alphabetical order.

Table 5-5.

Device Messages (1 of 5)

Message

What It Indicates

What To Do

Access level is

n ,

Read-only.

User’s access level is 2
or 3; user is not authorized
to change configurations.

No action needed.

Already Active

Test selected is already
running.

Allow test to continue.

Select another test.

Stop the test.

Blank Entries
Removed

New had been selected
from the Administer Logins
screen, no entry was made,
then Save was selected.

No action needed.

Reenter the Login ID,
Password, and Access Level.

Cannot delete Trap
Manager

De l ete was selected from
the Management PVCs
Options screen, but the
PVC had been defined as a
trap destination.

No action needed, or configure
another path for traps and try
again.

Command Complete

Configuration has been
saved or all tests have
been aborted.

No action needed.

Connection Refused

(Seen at an FTP
terminal.)

Two menu-driven user
interface sessions are
already in use when a
Telnet session was
attempted.

Wait and try again.

Destination Not
Unique

Destination entered is
already being used.

Enter another destination
indicator.

DLCI in connection.
Delete connection first

User tried to delete a DLCI
that was part of a
connection.

No action needed, or

Delete the connection, then
delete the DLCI.

Duplicate DLCI
Number

DLCI number entered is not
unique for the frame relay
link.

No action needed; previous
contents of the DLCI number
field is restored.

File Transfer Complete

(Seen at an FTP
terminal.)

A file transfer was
performed successfully.

Switch to the newly downloaded
software.

See

Changing Software

Содержание FrameSaver SLV 9664











































































































































































































































Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды

Paradyne FrameSaver SLV 9664, Руководство пользователя

Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды