Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 212

Страница: 212 / 240

SNMP MIBs and Traps, and RMON Alarm Defaults

B-26

9664-A2-GB20-00

March 2000

Table B-15.

Alarm OID Cross-Reference (1 of 2)

Object ID (OID)

Item

MIB/Tag

.1.3.6.1.2.1.10.32.2.1. . .

.1.3.6.1.2.1.10.32.2.1.4.I.D

Rx FECNs

MIB: FR DTE MIB (RFC 2115)

Tag: frCircuitReceivedFECNs

.1.3.6.1.2.1.10.32.2.1.5.I.D

Rx BECNs

MIB: FR DTE MIB (RFC 2115)

Tag: frCircuitReceivedBECNs

.1.3.6.1.2.1.10.32.2.1.6.I.D

Frames Sent

MIB: FR DTE MIB (RFC 2115)

Tag: frCircuitSentFrames

.1.3.6.1.2.1.10.32.2.1.7.I.D

Tx CIR Utilization

MIB: FR DTE MIB (RFC 2115)

Tag: frCircuitSentOctets

.1.3.6.1.2.1.10.32.2.1.7.I.D

Tx DLCI Link Utilization

MIB: FR DTE MIB (RFC 2115)

Tag: frCircuitSentOctets

.1.3.6.1.2.1.10.32.2.1.8.I.D

Frames Received

MIB: FR DTE MIB (RFC 2115)

Tag: frCircuitReceivedFrames

.1.3.6.1.2.1.10.32.2.1.9.I.D

Rx DLCI Link Utilization

MIB: FR DTE MIB (RFC 2115)

Tag: frCircuitReceivedOctets

.1.3.6.1.4.1.1795.2.24.2. . .

.1.3.6.1.4.1.1795.2.24.2.6.12.1.1.1.4.I

Unavailable Seconds

MIB: pdn_ IfExtTotal.mib (E)

Tag: pdnIfExtTotalUASs

.1.3.6.1.4.1.1795.2.24.2.6.9.4. . .

.1.3.6.1.4.1.1795.2.24.2.6.9.4.1.1.17.I.D

Tx Frames Exceeding CIR

MIB: pdn_FrExt.mib (E)

Tag: devFrExtDlciTxFrOutCIR

.1.3.6.1.4.1.1795.2.24.2.6.9.4.1.1.20.I.D

Frames Dropped by Network

MIB: pdn_FrExt.mib (E)

Tag: frFrExtDlciNetDropFr

.1.3.6.1.4.1.1795.2.24.2.6.9.4.1.1.23.I.D

Missing Latency Responses

MIB: pdn_FrExt.mib (E)

Tag: devFrExtDlciMissedSLVs

.1.3.6.1.4.1.1795.2.24.2.6.9.4.2.1.6.I.D

Congested Seconds

MIB: pdn_FrExt.mib (E)

Tag: devFrExtDlciStsCongestedSecs

.1.3.6.1.4.1.1795.2.24.2.6.9.4.2.1.2.I.D

DLCI Inactive Seconds

MIB: pdn_FrExt.mib (E)

Tag: devFrExtDlciStsInactiveSecs

.1.3.6.1.4.1.1795.2.24.2.6.9.4.3.1.5.I.D

Average Latency

MIB: pdn_FrExt.mib (E)

Tag: devFrExtLatencyAvg

Содержание FrameSaver SLV 9664











































































































































































































































Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды

Paradyne FrameSaver SLV 9664, Руководство пользователя

Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды