Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 240

background image

Configuration

3-25

9664-A2-GB20-00

March 2000

Table 3-5.

User Data Port Physical Interface Options (2 of 2)

Monitor DTR

Possible Settings: Enable, Disable
Default Setting: Enable

Specifies whether the state of the DTE Ready (DTR) circuit on the user data port will be
used to determine when valid data communication is possible with the DTE. When the
DTR off condition is detected, an alarm is generated, LMI is declared down, and no
further transfer of frame relay data can occur on this interface.

Display Conditions – This option does not appear when Port Type is set to X.21 (the
signal is assumed to be asserted).

Enable – Interchange circuit CD (ITU 108/1/2) – DTR is monitored to determine when
valid data is sent from the DTE.

Disable – DTR is not monitored. DTR is assumed to be asserted and data is being
transmitted, regardless of the state of the lead.

Monitor RTS (Control)

Possible Settings: Enable, Disable
Default Setting: Enable

Specifies whether the state of the Request To Send (RTS) circuits on the user data port
will be used to determine when valid data communication is possible with the DTE.
When the RTS off condition is detected, CTS is deasserted, LMI is declared down, and
no further transfer of frame relay data can occur on this interface.

Enable – Interchange circuit CA (ITU 105) – RTS is monitored to determine when valid
data communication is possible with the DTE.

Disable – RTS is not monitored. RTS is assumed to be asserted and data is being
transmitted, regardless of the state of the lead.

Port (DTE) Initiated Loopbacks

Possible Settings: Local, Disable
Default Setting: Disable

Allows a local external DTE Loopback to be started or stopped via the port’s attached
data terminal equipment using the port’s interchange lead LL (ITU 141).

Display Conditions – This option does not appear when Port Type is set to X.21 (the
signal is assumed to be asserted).

Local – The DTE attached to the port controls the local external DTE Loopback.

Disable – The DTE attached to the port cannot control the local external DTE
Loopback.

«
...
51
52
53
54
55
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Бренд: Panasonic Страницы: 44

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

IntroSpect Analyzer 2 Series

Бренд: Aruba Страницы: 5

Бренд: XtendLan Страницы: 228

Бренд: Ozenda Страницы: 116

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Бренд: LaCie Страницы: 67

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: Patton electronics Страницы: 2

S3000-EI Series

Бренд: Quidway Страницы: 16

Бренд: MiLAN Страницы: 155

Бренд: NetCommWireless Страницы: 28

Бренд: TRENDnet Страницы: 57

Wireless Outdoor Bridge XI-1500-IH

Бренд: IMC Networks Страницы: 13

Бренд: Tenda Страницы: 82

Бренд: ACTi Страницы: 12

Бренд: LevelOne Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды