Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 240

background image

Operation and Maintenance

5-5

9664-A2-GB20-00

March 2000

Table 5-2.

Network Interface LED

Label

Indication

Color

What It Means

OK

Operational
Status

Green

ON

– The interchange circuits for the

interface are in the correct state to
transmit and receive data.

OFF – A Loss of Signal (LOS) condition has

been detected on the leased line
network interface when it is not
transmitting INFO3 or receiving INFO4.

Table 5-3.

User Data Port LED

Label

Indication

Color

What It Means

OK

Operational
Status

Green

ON

– The interchange circuits for the port

are in the correct state to transmit and
receive data.

OFF – The port is idle. Occurs if the port is

configured to monitor DTR and/or RTS
and the lead(s) is not asserted.

Control Lead Descriptions

See Table 5-2,

Network Interface LED

, for a description of this lead. See

Table 5-3,

User Data Port LED

, to interpret the user data port OK control lead.

The LED descriptions and control lead descriptions are the same.

In addition to the OK LED for the user data port, additional control leads can be
monitored through the Display LEDs and Control Leads screen. These indicators
show the current state of each control lead and what they indicate when they are
highlighted; that is, in the On state. These are described in Table 5-4.

Table 5-4.

Additional User Data Port Control Leads

Label

Indication

What It Means

TXD

Transmit Data

Data is being sent to the far-end device.

RXD

Receive Data

Data is being received from the far-end device.

DTR

Data Terminal Ready

The Data Terminal Equipment (DTE) is not
ready to operate.

RTS

Request to Send

The DTE has indicated that it is ready to
transmit data.

«
...
97
98
99
100
101
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Бренд: Ubiquiti Страницы: 24

Бренд: 3Com Страницы: 20

Бренд: Patton electronics Страницы: 2

TokenLink 3C359B

Бренд: 3Com Страницы: 4

TokenLink 3C359B

Бренд: 3Com Страницы: 8

TokenLink 3C339

Бренд: 3Com Страницы: 2

EtherLink 3C985B-SX

Бренд: 3Com Страницы: 44

Бренд: 3Com Страницы: 88

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 111

TokenLink 3C359

Бренд: 3Com Страницы: 4

Бренд: 3Com Страницы: 74

Бренд: 3Com Страницы: 6

AT-8550/SP Series

Бренд: Allied Telesis Страницы: 114

Бренд: Belkin Страницы: 57

Бренд: IDT Страницы: 292

Husky HMG-1648EP

Бренд: Ethernet Direct Страницы: 16

Бренд: US Robotics Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды