Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 240

background image

Configuration

3-11

9664-A2-GB20-00

March 2000

Selecting a Frame Relay Discovery Mode

When a Frame Relay Discovery Mode is active, the FrameSaver unit “discovers”
network DLCIs from the network LMI status response message. It configures a
network DLCI, a user data port DLCI, and automatically connects them to create
a PVC.

Main Menu

→

Auto-Configuration

→

Frame Relay Discovery Mode

Automatically configured network DLCIs are multiplexed, and each automatically
configured port DLCI carries the same DLCI Number as its corresponding
network DLCI. These are the same DLCI numbers that would have been
available had the FrameSaver unit not been inserted in the link, between your
equipment and the network.

NOTE:

A local Management PVC (e.g., the PVC between the router and the
FrameSaver unit’s user data port) must be configured manually; it cannot
be configured automatically (see

Setting Up Local Management at the

Central Site

).

The following will occur when a Frame Relay Discovery Mode is selected:

Discovery Mode

Configuration Description

1MPort

(default)

H

Auto-configuration is enabled on Port-1.

H

A management DLCI is configured.

H

A multiplexed network DLCI containing two embedded
DLCIs (EDLCIs) is configured for Port-1 user data and
management data.

H

A PVC connection is configured between the network
and port DLCIs.

1Port

H

Auto-configuration is enabled on Port-1.

H

No management DLCI is configured.

H

A multiplexed network DLCI is configured for Port-1
user data.

H

A PVC connection is configured between the network
and port DLCIs.

NetOnly

H

Auto-configuration of a network DLCI only; no Port-1 or
PVC connections are configured.

H

No Port-1, PVC connection, or management DLCI is
configured.

Disable

H

No frame relay discovery or automatic configuration
takes place.

The FrameSaver unit will be configured manually.

«
...
37
38
39
40
41
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Бренд: D-Link Страницы: 38

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 20

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 12

DIR-615 - Wireless N Router

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 124

Web Smart DES-1210-28P

Бренд: D-Link Страницы: 6

2Voice + 4SW VoIP Router DVG-1402S

Бренд: D-Link Страницы: 57

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 23

Express EtherNetwork DI-604

Бренд: D-Link Страницы: 7

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 97

SharePort DIR-825

Бренд: D-Link Страницы: 2

Amplifi DIR-645

Бренд: D-Link Страницы: 28

Бренд: Clavister Страницы: 89

Бренд: Black Box Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды