Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 240

background image

Configuration

3-41

9664-A2-GB20-00

March 2000

Table 3-12.

Telnet and FTP Session Options (2 of 3)

Session Access Level

Possible Settings: Level-1, Level-2, Level-3
Default Setting: Level-1

Specifies the highest security level allowed when accessing the menu-driven user
interface via a Telnet session. If a login is required for the session, the effective access
level is also determined by the user’s access level. When a login is

not required, the

effective access level is determined by this option. This option does not affect the TS
Management Link.

NOTE:

The effective access level is always the lowest one assigned to either the
session or the user. For example, if the assigned Session Access Level is
Level-2, but the User Access Level is Level-3, then only level-3 access is
allowed for the session.

Level-1 – Allows Telnet access by users with Login ID access levels of 1, 2, and 3, with
the capability to view system information, change configuration options, and run tests.
This is the highest access level allowed.

Level-2 – Allows Telnet access by users with Login ID access levels of 1, 2, and 3, with
the capability to view system information and run tests only; they cannot change
configuration options.

Level-3 – Allows Telnet access by users with Login ID access levels of 1, 2, and 3, with
the capability to view system information only; they cannot change configuration options
or run tests.

Inactivity Timeout

Possible Settings: Enable, Disable
Default Setting: Enable

Determines whether a Telnet session is disconnected after a specified period of
keyboard inactivity.

Enable – Terminates the session after the Disconnect Time expires.

Disable – Does not terminate Telnet session during inactivity.

Disconnect Time (Minutes)

Possible Settings: 1 – 60
Default Setting: 10

Sets the amount of keyboard inactive time allowed before a user session is
disconnected.

Display Conditions – This option does not appear when Inactivity Timeout is disabled.

1 – 60 – Up to an hour can be set.

FTP Session

Possible Settings: Enable, Disable
Default Setting: Enable

Determines whether the system responds as a server when an FTP (file transfer
protocol) client on an interconnected IP network requests an FTP session. This option
must be enabled when downloading files.

Enable – Allows an FTP session between the system and an FTP client.

Disable – Does not allow FTP sessions.

«
...
67
68
69
70
71
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Бренд: 4IPNET Страницы: 97

Бренд: Fortinet Страницы: 20

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

Бренд: Matrix Switch Corporation Страницы: 61

Бренд: 4G Systems Страницы: 2

D-NVR4108HS-4KS2/L

Бренд: Dahua Страницы: 33

Бренд: Patton Страницы: 62

Бренд: Perle Страницы: 491

Total Access 1500 Dual FXS/DPO

Бренд: ADTRAN Страницы: 2

Бренд: Planet Страницы: 136

Бренд: Caimore Страницы: 79

Бренд: Planet Страницы: 16

Бренд: UltrArmor Страницы: 3

Бренд: UfiSpace Страницы: 34

Бренд: ubiquoss Страницы: 46

Бренд: Radionics Страницы: 100

BIPAC-741 GE V2.0

Бренд: Billion Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды