Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 240

background image

Troubleshooting

6-14

9664-A2-GB20-00

March 2000

PVC Tests

PVC tests can be run on a requested DLCI for a selected interface.

H

When PVC tests are on a multiplexed DLCI between FrameSaver devices,
they are nondisruptive to data, so user data can continue to be sent during
a test.

H

If the device at one end of the circuit is not a FrameSaver device, PVC tests
are on a standard DLCI and are disruptive to data. Also, the Connectivity test
would not appear.

Loopback, and send/monitor pattern tests are available for each interface on the
selected DLCI. FrameSaver devices should be at each end of the circuit. If a
PVC Loopback is started at one end of the circuit, the other end can send and
monitor pattern tests.

The example below shows a PVC Test screen for a FrameSaver unit with the
multiplexed DLCI 550 selected. If a standard DLCI was selected, (

Disruptive

),

rather than (

Non-Disruptive

), would be displayed after Test. Also, the

Connectivity test would not appear.

PVC Tests Screen Example

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

main/test/network_pvc

9664

Device Name: Node A

5/26/1999 23:32

NETWORK PVC TESTS

DLCI Number: 550

Test (Non-Disruptive)

Command

Status

Result

PVC Loopback:

Start

Inactive

0:00:00

Send Pattern:

Start

Inactive

0:00:00

Monitor Pattern:

Start

Inactive

0:00:00

Sequence Errors

99999+

Data Errors

99999+

Connectivity:

Start

Inactive

RndTrip Time (ms) 99999

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Ctrl-a to access these functions, ESC for previous menu

MainMenu

Exit

NOTE:

Errors encountered during these tests may be caused by mismatched CIRs
in the two FrameSaver devices. If errors are detected, verify the CIR
configuration and retest.

«
...
142
143
144
145
146
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Firebox SOHO 6 Wireless

Бренд: Watchguard Страницы: 8

Бренд: Salto Страницы: 2

Бренд: Patton electronics Страницы: 12

DSL5068EN(1T1R)

Бренд: Aztech Страницы: 40

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренд: CELOT Страницы: 34

Бренд: Techroutes Страницы: 20

AceroDURO 100/S100

Бренд: CNC-Step Страницы: 86

Бренд: Teldat Страницы: 23

Бренд: Ubiquiti Страницы: 20

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 17

Бренд: Cayman Systems Страницы: 170

Бренд: mikroElektronika Страницы: 6

Бренд: Korenix Страницы: 3

ICPE2600 Series

Бренд: 3onedata Страницы: 5

FrameSaver DSL 9783 CSU/DSU

Бренд: Paradyne Страницы: 233

Бренд: Billion Страницы: 12

Бренд: Cisco Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды