Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 240

background image

Configuration

3-52

9664-A2-GB20-00

March 2000

Table 3-15.

Communication Port Options (4 of 4)

Link Protocol

Possible Settings: PPP, SLIP
Default Setting: PPP

Specifies the link-layer protocol to be used. Only in effect when the COM port is
configured as a network communication link (Port Use option is set to Net Link).

Display Conditions – This option only appears when Port Use is set to Net Link.

PPP – Point-to-Point Protocol.

SLIP – Serial-Line Internet Protocol.

RIP

Possible Settings: None, Proprietary, Standard_out
Default Setting: None

Specifies which Routing Information Protocol (RIP) is used to enable routing of
management data between devices.

Display Conditions – This option only appears when Port Use is set to Net Link.

None – No routing is used.

Proprietary – A proprietary variant of RIP version 1 is used to communicate routing
information only between devices to enable routing of IP traffic.

Standard_out – The device will send standard RIP messages to communicate routing
information about other FrameSaver units in the network. Standard RIP messages
received on this link are ignored.

NOTE:

The router must be configured to receive RIP on the port connected to the
COM port, configured as the management interface (e.g., Cisco:

config-t, router RIP, int serial

x, IP RIP Receive

version 1, ctl-z WR

).

To create this management interface, make sure that Node or COM port IP
Information has been set up (

Configuring Node IP Information

).

«
...
78
79
80
81
82
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Module NI PXI-8250

Бренд: National Instruments Страницы: 39

Бренд: Conceptronic Страницы: 230

Бренд: NetBurner Страницы: 15

Бренд: Allied Telesis Страницы: 1

Бренд: Lanner Страницы: 63

RabbitCore RCM4400W

Бренд: Rabbit Страницы: 126

ControlPoint 2000

Бренд: 4Home Страницы: 20

Бренд: Belkin Страницы: 2

MMAC-Plus 9G536-04

Бренд: Cabletron Systems Страницы: 42

PXI Terminal Block NI TB-2709

Бренд: National Instruments Страницы: 12

Бренд: Ubiquiti Страницы: 20

Бренд: Milesight Страницы: 15

TE100S8P - Fast Ethernet Switch

Бренд: TRENDnet Страницы: 11

JetNet 5720G-8P Series

Бренд: Korenix Страницы: 52

Бренд: Commax Страницы: 122

ForeFront 2616RC

Бренд: Patton electronics Страницы: 80

Бренд: MasterForce Страницы: 12

Бренд: Actelis Networks Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды