Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 114

Страница: 114 / 240

Operation and Maintenance

5-20

9664-A2-GB20-00

March 2000

Network Interface Status

The network interface status is selected from the Status menu.

Main Menu

→

Status

→

Network Interface Status

Table 5-11.

Network Interface Status (1 of 2)

Field

Status

What It Indicates

Operating Rate (Kbps)

The frame relay network’s operating
rate as detected by the unit’s
network interface.

64 kbps

128

128 kbps

Disconnected

The line was disconnected.

Interface State

Shows the state of the leased line
BRI S/T network interface.

Deactivated(F3)

No signals are being transmitted
by the unit or network DSU(NT1).

Synchronized(F6)

The unit has synchronized
with the attached network
DSU(NT1), but the activation
signal (INFO4) has not yet been
received.

Activated(F7)

Data is being transmitted and
received on the interface.

Lost Framing(F8)

The unit has lost framing and
is attempting to resynchronize
with the attached network
DSU(NT1).

Transmit Signal

Shows the signals being sent from
the leased line BRI S/T network
interface toward an attached
DSU(NT1).

INFO0

No Signal Indication. This occurs
when the unit is first connected,
when power is applied, or when
frame alignment is lost.

INFO3

Synchronized frames are being
transmitted. This occurs when
frame alignment is established,
but the activation signal (INFO4)
has not yet been received.

Until the activation signal is
received, data transmission
cannot be assured.

Содержание FrameSaver SLV 9664











































































































































































































































Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды

Paradyne FrameSaver SLV 9664, Руководство пользователя

Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды