Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 240

background image

Troubleshooting

6-4

9664-A2-GB20-00

March 2000

Restoring Communication with a Misconfigured Unit

Misconfiguring the unit could render the menu-driven user interface inaccessible.
If this occurs, connectivity to the unit can be restored via a directly connected
asynchronous terminal.

"

Procedure

To reset COM port settings:

1. Configure the asynchronous terminal to operate at 19.2 kbps, using character

length of 8 bits, with one stop-bit, and no parity. In addition, set Flow Control
to None.

2. Reset the unit, then hold the Enter key down until the System Paused screen

appears. (See

Resetting the Unit and Restoring Communication

for other

methods of resetting the unit.)

3. Tab to the desired prompt, and type y ( Yes) at one of the prompts.

If selecting . . .

The following occurs . . .

Reset COM Port usage

H

Port Use is set to Terminal so the asynchronous
terminal can be used.

H

Data Rate (Kbps), Character Length, Stop Bits,
and Parity are reset to the factory defaults.

H

Unit resets itself.

Reload Factory Defaults

H

All configuration and control settings are reset to
the Default Factory Configuration, overwriting the
current configuration.

H

Unit resets itself.

CAUTION: This causes the current configuration to

be destroyed and a self-test to be
performed.

If no selection is made within 30 seconds, or if No (n) is entered, the unit
resets itself and no configuration changes are made.

Once the unit resets itself, connectivity is restored and the Main Menu screen
appears.

«
...
132
133
134
135
136
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Бренд: 3Com Страницы: 20

Бренд: Sagem Страницы: 19

Бренд: Profile Страницы: 6

Бренд: H3C Страницы: 26

Бренд: FS Страницы: 19

Бренд: Moxa Technologies Страницы: 36

301300U - Ethernet Disk NAS Server

Бренд: LaCie Страницы: 62

Бренд: Talent Страницы: 18

Бренд: SriHome Страницы: 12

Бренд: NetComm Страницы: 75

Бренд: Proscend Страницы: 93

TEG-S16R - DATA SHEETS

Бренд: TRENDnet Страницы: 12

LN1000 - RELEASE NOTES 8-27-2010

Бренд: Juniper Страницы: 64

ReadyNAS Duo v2

Бренд: NETGEAR Страницы: 100

Бренд: TRENDnet Страницы: 3

Бренд: NAUTICAST Страницы: 20

Бренд: X-Micro Страницы: 24

Бренд: H3C Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды