Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 138

Страница: 138 / 240

Troubleshooting

6-8

9664-A2-GB20-00

March 2000

Table 6-1.

Alarm Conditions (2 of 3)

Alarm Condition

What To Do

What It Indicates

LMI Down,
frame relay link

The Local Management
Interface is down for the
specified frame relay link.

For the network data port:

If LMI was never up, verify
that the LMI Protocol setting
reflects the LMI type being
used.

If LMI was never up:

Verify that Frame Relay
Performance Statistics show
LMI frames being transmitted.

If all of the above have been
verified and the physical link is
not in Alarm, contact your
network provider.

For user data port:

Check that the DTE cable is
securely attached at both
ends.

Verify that Transmit Clock
Source and Invert Transmit
Clock options are properly
configured.

Verify that Frame Relay
Performance Statistics show
LMI frames being received. If
no frames are being received:

– Check the attached device.

– Verify that the LMI Protocol

setting reflects the LMI type
being used.

LOS at Network 1

A Loss of Signal (LOS)
condition is detected on the
leased line BRI S/T network
interface when it is not
transmitting INFO3 or
receiving INFO4.

Network cable problem.

No signal is being
transmitted at the far-end
FrameSaver unit.

T1 facility problem.

DSU(NT1) or leased-line
network facility problem.

Check that the network cable
is securely attached at both
ends.

Contact your network provider.

frame relay link is one of the following:
– Net1-FR1. The frame relay link specified for the network data port, Network 1.

– Port-1. The frame relay link associated with the user data port.

Содержание FrameSaver SLV 9664











































































































































































































































Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды

Paradyne FrameSaver SLV 9664, Руководство пользователя

Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды