Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 240

background image

Configuration

3-45

9664-A2-GB20-00

March 2000

Table 3-14.

SNMP Traps and Trap Dial-Out Options (2 of 5)

Initial Route Destination

Possible Settings: AutoRoute, COM,

PVCname

Default Setting: AutoRoute

Specifies the initial route used to reach the specified Trap Manager. When proprietary
RIP is active, only one unit in the network needs to specify an interface or management
link as the initial destination. All other units can use the default setting.

Display Conditions – This option appears for each trap manager specified in the
Number of Trap Managers configuration option.

AutoRoute – Uses proprietary RIP from other FrameSaver devices to learn the route
for sending traps to the specified Trap Manager, or the Default IP Destination when no
route is available in the routing table (see

Table 3-9,

Node IP Options

).

COM – Uses the COM port. This selection is only available when Port Use is set to
Net Link (see

Table 3-15,

Communication Port Options

).

PVCname – Uses the defined management linkname (the name given the Management
PVC). This selection only appears when at least one Management PVC is defined for
the node.

General Traps

Possible Settings: Disable, Warm, AuthFail, Both
Default Setting: Both

Determines whether SNMP trap messages for warmStart and/or authenticationFailure
events are sent to the currently configured trap manager(s).

Disable – Does not send trap messages for these events.

Warm – Sends trap messages for warmStart events only.

AuthFail – Sends trap messages for authenticationFailure events only.

Both – Sends trap messages for both warmStart and authenticationFailure events.

Enterprise Specific Traps

Possible Settings: Enable, Disable
Default Setting: Disable

Determines whether trap messages for enterpriseSpecific events are sent to the
currently configured trap manager(s).

Enable – Sends trap messages for enterpriseSpecific events.

Disable – Does not send trap messages for enterpriseSpecific events.

«
...
71
72
73
74
75
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Бренд: PaloAlto Networks Страницы: 2

Бренд: Ubiquiti Страницы: 22

UniFi UAP-AC-LR

Бренд: Ubiquiti Страницы: 28

Бренд: Datasheen Страницы: 25

Бренд: iBall Baton Страницы: 9

RUGGEDMAX WIN7000

Бренд: RuggedCom Страницы: 42

PBE-5AC-300-ISO

Бренд: Ubiquiti Страницы: 28

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

Meridian 1 Option 11C Mini

Бренд: Meridian Страницы: 546

Бренд: Tripp Lite Страницы: 2

Бренд: Porter-Cable Страницы: 6

3GStation Professional

Бренд: Ubiquiti Страницы: 24

BiPAC 8200AXL-1200

Бренд: Billion Страницы: 94

Бренд: Cisco Страницы: 28

LINKSYS WUSB54GR

Бренд: Cisco Страницы: 205

Бренд: Cisco Страницы: 37

Бренд: Cisco Страницы: 23

Linksys RVS4000

Бренд: Cisco Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды