Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 240

background image

Setting Up NetScout Manager Plus for FrameSaver Devices

8-8

9664-A2-GB20-00

March 2000

Adding SLV Alarms Using a Template

Once DLCIs have been discovered, SLV alarms should be configured and
assigned to each DLCI. OpenLane provides a template for configuring alarms.
DLCI alarms can be configured manually, but using the Paradyne alarm defaults
template greatly reduces configuration time.

The following alarms are configured for each DLCI included in the Paradyne MIB:

— Frames Sent (SLVFramesSnt)

— Rx DLCI Utilization (SLVrxDLCIUtil)

— Tx CIR Utilization (SLVTxCIRUtil)

— Frames Sent Above CIR
(SLVFramesTxAbvCIR)

— Tx DLCI Utilization (SLVTxDLCIUtil)

— Average Latency (AverageLatency)

— Frames Received (SLVFramesRec)

— Current Latency (CurrentLatency)

These alarms and current values can be found in $NSHOME/usr/slvtemplate.fct,
which is used as a starting point for loading new alarms. This file can be copied
and edited so the alarm threshold values match service level agreement values.
The copied .fct file can then be used to replicate alarm threshold values for all
DLCIs on the unit using the eztrap utility. All .fct files must be in $NSHOME/usr.

To configure alarms manually, see

Adding SLV Alarms Manually

.

NOTE:

Perl must be installed in your system to use the eztrap utility in the procedure
below. If you have an NT system, please install Perl before proceeding.

"

Procedure

1. Open a terminal window and go to $NSHOME/usr.

2. Type eztrap -i

filename.fct -o agentname.fct agentname and press Enter to

run the eztrap utility to create alarm threshold values across all DLCIs for the
copied .fct file.

The message

eztrap done

appears when the .fct file is transferred.

3. From the NetScout Manager Plus main window, with the FrameRelay and

Admin radio buttons still selected, click on the Config Manager icon to open
the Configuration Manager main window.

4. Edit any alarm values that need to be changed.

5. Select the Install button (down the center of the Configuration Manager

main window) to load alarms for the unit. This may take some time, so
please be patient.

See

Editing Alarms

if any default settings need to be changed.

«
...
158
159
160
161
162
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Sure Cross DX70

Бренд: Banner Страницы: 35

Бренд: Intellinet Страницы: 2

Net2Air Ins-40085-US

Бренд: Paxton Страницы: 4

Бренд: ZyXEL Communications Страницы: 215

Бренд: EVOC Страницы: 57

InvenSense RoboKit1

Бренд: TDK Страницы: 13

Бренд: NC-link Страницы: 20

LonWorks Communication Module LN-01

Бренд: Delta Electronics Страницы: 1

SmartSTACK ELS100-24TXM

Бренд: Cabletron Systems Страницы: 117

Бренд: TP-Link Страницы: 113

Бренд: VIA Technologies Страницы: 25

Бренд: ATTO Technology Страницы: 2

Бренд: TRENDnet Страницы: 10

Бренд: Thecus Страницы: 130

Бренд: NetCommWireless Страницы: 28

Бренд: B&B Electronics Страницы: 2

Бренд: AMG Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды