manualshive.com logo in svg

Paradyne FrameSaver SLV 9664, Руководство пользователя

Построенный на инновационной технологии Paradyne FrameSaver SLV 9664 обеспечивает надежную защиту вашего устройства. Для получения подробной информации об использовании рекомендуется скачать бесплатное руководство пользователя с нашего веб-сайта. Не упустите возможность загрузить его сейчас с manualshive.com.

Поделиться
Скачать
background image

Configuration

 3-23

9664-A2-GB20-00

March 2000

Configuring the Physical Interfaces

Characteristics for the following physical interfaces can be configured:

H

Network Interface

H

User Data Port

Configuring the Network Interface

Select Physical to display or change the physical configuration options for the
port being used as the network interface (see Table 3-4).

Main Menu

→

Configuration

→

Network

→

Physical

Table 3-4.

Network Physical Interface Options

Network Initiated DCLB

Possible Settings: Disable, V.54
Default Setting: V.54

Allows the initiation and termination of the Data Channel Loopback (DCLB V.54 Loop 2)
to be controlled by the receipt of a DCLB-actuate or DCLB-release sequence (either
V.54 or FT1-ANSI compliant) from the network on the B-channels used for the network
frame relay link. When enabled and a DCLB-activate sequence is received, the unit
initiates a DCLB on the network interface. When a DCLB-release sequence is received,
the DCLB is stopped.

Disable – DCLB-actuate and DCLB-release sequences are ignored.

V.54 – DCLB-actuate and DCLB-release sequences that comply with either V.54 or
ANSI T1.403, Annex B standard will be recognized and will control initiation and
termination of a DCLB for the network frame relay link. The actuate and release
sequences do not need to match (for example, a DCLB started with a V.54 actuate
sequence can be stopped with an FT1 release sequence).

Operating Rate (Kbps)

Possible Settings: Autorate, 64, 128
Default Setting: Autorate

Specifies the line rate, or automatic detection of the line rate, on the leased line BRI S/T
network interface.

Autorate – The rate is automatically detected by the unit by attempting to bring up the
frame relay LMI on one or both channels.

64 or 128 – Specifies the network operating rate to either 64 kbps or 128 kbps;
automatic rate detection is disabled.

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Tripp Lite N125-010-GY Specification Sheet preview
N125-010-GY
Бренд: Tripp Lite Страницы: 2
American Megatrends StorTrends 1312-P Specifications preview
StorTrends 1312-P
Бренд: American Megatrends Страницы: 2
AOpen 4-Port 10/100Mbps Ethernet Broadband Router User Manual preview
4-Port 10/100Mbps Ethernet Broadband Router
Бренд: AOpen Страницы: 41
TP-Link Deco XE200 User Manual preview
Deco XE200
Бренд: TP-Link Страницы: 57
MA lighting 8Port Node Quick Manual preview
8Port Node
Бренд: MA lighting Страницы: 49
Vacron VDH-NK300 Hardware Manual preview
VDH-NK300
Бренд: Vacron Страницы: 16
Broadband Products D-Link DSL-2640U Quick Installation Manual preview
D-Link DSL-2640U
Бренд: Broadband Products Страницы: 12
Linksys WRK54G User Manual preview
WRK54G
Бренд: Linksys Страницы: 80
Beckhoff EK1122 Documentation preview
EK1122
Бренд: Beckhoff Страницы: 84
Rajant BreadCrumb ES1 User Manual preview
BreadCrumb ES1
Бренд: Rajant Страницы: 93
Axis M31-L SERIES Installation Manual preview
M31-L SERIES
Бренд: Axis Страницы: 30
TheGreenBow IPSec VPN Client Zyxel ZyWall 10 Configuration Manual preview
IPSec VPN Client Zyxel ZyWall 10
Бренд: TheGreenBow Страницы: 12
Supero AOC-SIMLP-3+ User Manual preview
AOC-SIMLP-3+
Бренд: Supero Страницы: 66
UltrArmor UA3 Series User Manual preview
UA3 Series
Бренд: UltrArmor Страницы: 3
UfiSpace S9601-104BC Hardware Installation Manual preview
S9601-104BC
Бренд: UfiSpace Страницы: 34
ubiquoss U9016B Installation Manual preview
U9016B
Бренд: ubiquoss Страницы: 46
Billion BiPAC 7402VGO Specifications preview
BiPAC 7402VGO
Бренд: Billion Страницы: 2
MTL 9468-ET Instruction Manual preview
9468-ET
Бренд: MTL Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды