Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 197

Страница: 197 / 240

SNMP MIBs and Traps, and RMON Alarm Defaults

B-11

9664-A2-GB20-00

March 2000

Traps: enterprise-Specific

These traps indicate that an enterprise-specific event has occurred. Supported
enterprise-specific traps are listed below.

Table B-7.

enterprise-Specific Traps and Variable-Bindings (1 of 2)

Trap

Variable-Bindings

Possible Cause

enterpriseCIR-
Change(15)

devFrExtDlciIfIndex
(devFrExt.mib)

devFrExtDlciDlci
(devFrExt.mib)

devFrExtDlciCIR
(devFrExt.mib)

devLastTrapString
(devHealthAndStatus.-

mib)

CIR has changed due to the LMI
report. LMI Protocol is set to
Standard and the network’s CIR
changed.

String:
‘CIR on $ifString changed to
$CIR bps.’

enterpriseConfig-
Change(6)

devLastTrapString
(devHealthAndStatus.-
mib)

Configuration has been changed
via the menu-driven user
interface, an SNMP Manager,
or auto-configuration after 60
seconds has elapsed without
another change.

String:
‘Device configuration change.’

enterpriseDLCI-
delete(17)

devFrExtDlciIfIndex
(devFrExt.mib)

devFrExtDlciDlci
(devFrExt.mib)

devLastTrapString
(devHealthAndStatus.-

The DLCI has been deleted. The
network no longer supports the
DLCI, and it was removed.

Strings:
‘$ifString deleted by Auto-DLCI
delete.’

enterpriseDLCI-
Down(11)

(devHealthAndStatus.-
mib.)

DLCI Status is set to Inactive; the
DLCI is down.

Strings:
‘$ifString down.’ (Due to LMI or
physical failure.)

‘$ifString administratively
shutdown.’ (Due to an intentional
shutdown.)

enterpriseDLCIUp(12)

DLCI Status is set to Active;
DLCI is up again.

String:
‘$ifString up.’

Содержание FrameSaver SLV 9664











































































































































































































































Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды

Paradyne FrameSaver SLV 9664, Руководство пользователя

Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды