Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 240

background image

Configuration

3-15

9664-A2-GB20-00

March 2000

Setting Up So the Router Can Receive RIP

Using the system’s standard Routing Information Protocol (RIP) feature, routing
information is passed to the router over the management PVC, so the router can
learn routes to FrameSaver SLV devices. Node IP information should be set up
(see

Configuring Node IP Information

).

"

Procedure

1. Configure the router to receive RIP.

For example, if using a Cisco router, configure

config-t

,

router RIP

,

int serial

x

,

IP RIP Receive version 1

, then

ctl-z WR

.

2. Create a Standard DLCI for the user data port.

Configuration

→

Data Ports

→

DLCI Records

3. Create a Management PVC using the user data port DLCI just configured.

Configuration

→

Management and Communication

→

Management PVCs

4. Set Primary Link RIP to Standard_Out, and Save the configuration.

Refer to Table 3-7,

DLCI Record Options

, and Table 3-10.

Management PVC

Options

for configuration information.

Setting Up Service Provider Connectivity at the Central Site

When management needs to be set up between a service provider’s customer
and its network operations center (NOC), a non-multiplexed DLCI must be
configured to carry management data between the customer’s central site and
the NOC console. This requires that a frame relay discovered DLCI needs to be
modified. This is because all auto-configured network DLCIs are configured as
multiplexed DLCIs.

"

Procedure

To set up NOC management:

1. Select DLCI Records on the network interface.

Configuration

→

Network

→

DLCI Records

2. Select Modify. The

Modify DLCI Record for DLCI Number

prompt

appears.

3. Select the DLCI that will be used by pressing the spacebar until the correct

DLCI number appears, then select it.

4. Change the DLCI Type from Multiplexed to Standard.

The

DLCI in connections. Update DLCI usage as follows:

prompt appears.

«
...
41
42
43
44
45
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Бренд: Qlogic Страницы: 2

Бренд: Qlogic Страницы: 172

Бренд: Amperes Страницы: 8

Бренд: Profile Страницы: 6

Бренд: ZyXEL Communications Страницы: 485

Бренд: NETGEAR Страницы: 2

Бренд: Magnadyne Страницы: 8

RS-232/422/485 Serial Card CE 3PXCC4A

Бренд: B&B Electronics Страницы: 47

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

Бренд: Juniper Страницы: 2

IPLink 2603 Series

Бренд: Patton Страницы: 120

Бренд: Network Critical Страницы: 200

Husky HMG-1648EP

Бренд: Ethernet Direct Страницы: 16

NetVanta Analog Modem Dial Backup Interface Module

Бренд: ADTRAN Страницы: 2

Бренд: Lanner Страницы: 99

7798 I/SITE LAN

Бренд: CSI Страницы: 56

Бренд: EINHELL Страницы: 32

Бренд: YDI Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды