Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 240

background image

A

9664-A2-GB20-00

March 2000

Copyright

E

2000 Paradyne Corporation.

All rights reserved.
Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form
or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the
express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.

Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for any help needed. For
additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor
locations, or Paradyne worldwide office locations, use one of the following methods:

H

Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at
www.paradyne.com/warranty.)

H

Telephone: Call our automated system to receive current information by fax or to speak with a company
representative.

— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to [email protected]. Include
the number and title of this document in your correspondence. Please include your name and phone number if you
are willing to provide additional clarification.

Trademarks

ACCULINK, COMSPHERE, FrameSaver, and Hotwire are registered trademarks of Paradyne Corporation.
NextEDGE, MVL, OpenLane, Performance Wizard, and TruePut are trademarks of Paradyne Corporation. All other
products and services mentioned herein are the trademarks, service marks, registered trademarks, or registered
service marks of their respective owners.

Patent Notification

FrameSaver SLV products are protected by U.S. Patents: 5,550,700 and 5,654,966. Other patents are pending.

«
1
2
3
4
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

NetDefend DFL-260E

Бренд: D-Link Страницы: 328

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

DFL-210 - NetDefend - Security Appliance

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 22

Бренд: Dahua Страницы: 12

NetDefend DFL-1600

Бренд: D-Link Страницы: 23

Бренд: H3C Страницы: 12

4-Port 10/100Mbps Ethernet Broadband Router

Бренд: AOpen Страницы: 41

Бренд: ZyXEL Communications Страницы: 422

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

Бренд: Draytek Страницы: 2

Бренд: Genie Страницы: 6

Бренд: Moxa Technologies Страницы: 2

Бренд: axing Страницы: 4

Бренд: Ozenda Страницы: 116

Бренд: Aviosys Страницы: 77

GigaVUE H TA100-CXP

Бренд: Gigamon Страницы: 115

Бренд: Dinstar Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды