Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 240

background image

Troubleshooting

6-7

9664-A2-GB20-00

March 2000

Alarms

The following table describes the alarm conditions that will generate an SNMP
trap for a physical interface, and the frame relay LMIs and DLCIs. These alarm
conditions also generate Health and Status messages seen on the System and
Test Status screen.

Main Menu

→

Status

→

System and Test Status

Table 6-1.

Alarm Conditions (1 of 3)

Alarm Condition

What It Indicates

What To Do

CTS down to
Port-1

Device

The CTS control lead on
the device’s interface is off.

Check DTR and RTS from
Port-1.

H

Verify that the port is enabled.

H

Check DTR from the user data
port.

DLCI

nnnn Down,

frame relay link

1, 2

The DLCI for the specified
frame relay link is down.

Verify that the network LMI is up.
If it is, contact your network
service provider.

DTR down from Port-1
Device

The DTR control lead on
the device connected to
Port

-n is disasserted.

Examine the attached DTE and
cable connected to the
FrameSaver unit’s port.

H

Check that the Port

-1 cable is

securely attached at both
ends.

H

Check the status of the
attached equipment.

1

nnnn indicates a DLCI number of 16 through 1007.

2

frame relay link is one of the following:

– Net1-FR1. The frame relay link specified for the network data port, Network 1.

– Port-1. The frame relay link associated with the user data port.

«
...
135
136
137
138
139
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: Usr Страницы: 2

totalstorage 200

Бренд: IBM Страницы: 152

Бренд: Teletronics International Страницы: 57

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Бренд: LaCie Страницы: 67

Бренд: Idis Страницы: 22

Бренд: BinTec Страницы: 34

Бренд: Keysight Technologies Страницы: 106

Бренд: E-Lins Страницы: 10

Бренд: H3C Страницы: 62

Бренд: Proxim Страницы: 65

Бренд: TP-Link Страницы: 2

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Бренд: LaCie Страницы: 74

Router 3000 Series

Бренд: 3Com Страницы: 37

Бренд: Sarian Systems Страницы: 9

Бренд: GRASS VALLEY Страницы: 22

Бренд: Huawei Страницы: 3

Бренд: Johnson Controls Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды