Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 240

background image

Configuration

3-28

9664-A2-GB20-00

March 2000

Table 3-6.

Interface Frame Relay Options (3 of 3)

LMI Inbound Heartbeat (T2)

Possible Settings: 5, 10, 15, 20, 25, 30
Default Setting: 15

Configures the LMI-defined T2 parameter, which sets the number of seconds between
the receipt of status enquiry messages on the network side of the LMI. Applies to the
network side of a UNI only.

5 – 30 – Specifies the number of seconds between the receipt of status enquiry
messages in increments of 5.

LMI N4 Measurement Period (T3)

Possible Settings: 5, 10, 15, 20, 25, 30
Default Setting: 20

Configures the LMI-defined T3 parameter, which is the time interval (in seconds) that the
network side of the LMI uses to measure the maximum number of status enquiry
messages that have been received (N4) from the user side.

5 – 30 – Specifies the interval of time in increments of 5.

Manually Configuring DLCI Records

The Auto-Configuration feature automatically configures DLCI Records and their
PVC Connections. DLCI Records can also be created manually (see Table 3-7).

Main Menu

→

Configuration

→

[Network/Data Ports]

→

DLCI Records

Typically, DLCI Records only need to be configured when building Management
PVCs between the NOC and the central site unit; the unit automatically
configures non-management DLCI Records and PVC Connections.

Table 3-7.

DLCI Record Options (1 of 3)

DLCI Number

Possible Settings: 16 – 1007
Default Setting: Initially blank; no default.

Specifies the number for the DLCI in the DLCI record. The parameter determines which
DLCI record is used for transferring data on a particular frame relay interface. DLCI
numbers range from 0 to 1023. However, the numbers 0 – 15 and 1008 – 1023 are
reserved. Entry of an invalid number results in the error message

Value Out of

Range (16 – 1007)

. If the DLCI number is part of a connection, this field is read-only.

NOTES: – If a DLCI number is not entered, the DLCI record is not created.

– The DLCI number entered must be unique for the interface.

– Changing settings for this configuration option causes the FrameSaver

unit to abort any active frame relay tests.

16 – 1007 – Specifies the DLCI number.

«
...
54
55
56
57
58
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

Бренд: Panasonic Страницы: 2

Бренд: H3C Страницы: 22

Бренд: H3C Страницы: 3

Бренд: PaloAlto Networks Страницы: 3

Бренд: Zhone Страницы: 7

Бренд: Zhone Страницы: 1

Бренд: Zonet Страницы: 10

Бренд: Samsung Страницы: 65

Бренд: Dahua Страницы: 6

ZyXEL EES-1024AF

Бренд: ZyXEL Communications Страницы: 99

Бренд: LaCie Страницы: 22

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Бренд: Garderos Страницы: 23

RabbitCore RCM4400W

Бренд: Rabbit Страницы: 126

ControlPoint 2000

Бренд: 4Home Страницы: 20

Бренд: WABCO Страницы: 29

SteelCentral AppResponse 2180

Бренд: Riverbed Страницы: 82

EdgeRouter PoE ERPoe-5

Бренд: Ubiquiti Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды