APPLIED OPERATIONS
/ Merger/Extraction of Image Channels
IV.
OPERATION INSTRUCTIONS
IV .
2 - 3 3 3
Page
2-14 Merger/Extraction of Image Channels
2-14-1 Setting the Range of Multiple Image Slices
When merging or extracting channels in images composed of multiple image slices,
such as time-lapse images and images acquired by varying the cross-sections, it is
possible to select only some of image slices as the target of channel merger or
extraction. This section describes how to set the range of target image slices.
1.
Display the [Display] panel of the images composed of multiple image slices.
2. The buttons as shown below are displayed at the top of the [Display] panel. To
switch to the image slice of another cross-section , click the <Z/T series switch>
button then click the <XYZ series> button in the displayed list of buttons. To switch
to the image slice of another instant in the elapsed time, click the <Z/T series
switch> button then click the <XYT series> button in the displayed list of buttons.
(In these operations, the icon in the <Z/T series switch> button changes to the icon
of the selected button.)
x x x
<XYZ series> button
Displays one of multiple images by selecting
it according to the cross-section (Z).
<Set start position> button
When successive display or frame-by-frame display is
required, set the image with which the display should
start. (“0” is set when this button is not used.)
<Display> button
Press to start display of n-slices of image from the start position to the end position sequentially
(successive display) or one (frame-by-frame display) or to stop successive display.
Holding the button displays image slices in successive display and clicking it displays image
slices by advancing frame by frame.
<Display> button
Press to start display of n-slices of image from the end position to the start position sequentially
(successive display) or one (frame-by-frame display) or to stop successive display.
Holding the button displays image slices in successive display and clicking it displays image slices by
advancing frame by frame.
<Bound> button
Every time successive display or frame-by-frame display in a direction
ends at the start or end position, the display is restarted in the opposite
direction.
<Set end position> button
When successive display or frame-by-frame display is
required, set the image with which the display should
end. (Assuming that the number of images is n, “n-1” is
set when this button is not used.)
<Z/T series switch> button
<XYT series> button
Displays one of multiple images by selecting
it according to the time (T).
<Loop> button
Successive display or frame-by-frame display is
repeated in the same direction.
<Loop/Bound switch> buttons
<Display speed switch> buttons
Set the speed of successive display.
<Rabbit> button
Press for successive display of image slices without pause.
<Clock> button
Press for successive display of image slices at the time interval set in the [Time series] sub-panel.
<Turtle> button
Press for successive display of image slices at an interval of 0.8 sec.
Содержание FLUOVIEW FV300
