Ness D24 Скачать руководство пользователя страница 46

Страница: 46 / 60

O P E r a T i O N

neSS D24 Control Panel - inStallation & PrograMMing Manual

viEw mENu

the VieW menu can be used at any time to display the status of Zone, tamper,
System and Power inputs.

the status of these inputs can be displayed “live” as it happens, or as a previous
event in Memory mode.

to VIeW A CUrreNt ALArm:

Press...

the MeMory icon will be on

and one of the system icons

ZONE

TAMPER

SYSTEM

POWER

along with a number to indicate

which alarm is present. if there is no current outstanding alarm, pressing VieW
from the normal zone display mode will display the last event.

to VIeW tHe StAtUS of ALL ALArmS:

Press...

[repeat presses]

repeated presses of the VieW button will cycle viewing of Zone, tamper, System,
Power and Memory sub-menus.
or, each sub-menu can be directly viewed by pressing

[1–6]

DefAULt VIeW

the display always shows the
zone menu by default.

it will automatically revert back
to the Zone menu after eight
seconds if left in any other view
menu.

to VIeW ZoNeS

ZONE

Press...

the zone indicators 1–24 will show the state of the 24 zones and possibly one or more other
icons flashing to indicate other alarms.

to VIeW tAmPerS

TAMPER

Press...

Zone indicators will show the state of the four tamper inputs:

tAmPer 1:

external tamper alarm.

tAmPer 2:

Control Panel tamper alarm.

tAmPer 3:

Zone input tamper alarm.

tAmPer 5:

radio interface tamper alarm.

to VIeW SYStem

SYSTEM

Press...

Zone indicators will show the state of the eight System inputs:

SYStem 1:

Keyswitch Panic

SYStem 2:

Dialler line fault

SYStem 3:

Keypad connection fault

SYStem 4:

Control panel fault

SYStem 5:

Duress alarm

SYStem 6:

Panic alarm

SYStem 7:

Medical alarm

SYStem 8:

user Code alarm

SYStem 9:

access to installer Program mode

to VIeW PoWer

POWER

Press...

Zone indicators will show the state of the six Power alarms:

PoWer 1:

Mains power failure

PoWer 2:

Control panel backup battery is low

PoWer 3:

DC supply failure

PoWer 4:

Zone reference power failure

PoWer 9:

radio device battery low. (Zone indicators 1–8 will show which device)

PoWer 0:

radio Key battery low. (Zone indicators 1–8 will show which radio Key)

This is the normal display while disarmed
with no outstanding alarms. The ZONE icon

is on as well as any number 1 to 24 if zones

are being unsealed.

Tamper numbers will be on only if there
are Tamper alarms to view.

Zone numbers will be on only if there are

unsealed zones or alarmed zones to view.

System numbers will be on only if there
are System alarms to view.

Power numbers will be on only if there are
Power alarms to view.

Содержание D24





























































Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды

Ness D24, Инструкция по установке и программированию

Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды