Ness D24 Скачать руководство пользователя страница 35

Страница: 35 / 60

diallEr - PrOgrammiNg

D. Prog

neSS D24 Control Panel - inStallation & PrograMMing Manual

OPTION No DESCRIPTION

DEFAULT

P750E
P751E
P752E
P753E

ADMIN Area client code
AREA 1client code
AREA 2client code
AREA 3client code

0000
0000
0000
0000

arEa CliENT COdES

these options are for programming individual client codes for each area. option
P60e 3e must also be on.

P750e

admin area client code.

P751e

area 1 client code.

P752e

area 2 client

code.

P753e

area 3 client code.

P750e–P753e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

0000

tO prOgraM:

[

[Client Code]

related OptIOns:

P60E 3E, Send Open/Close with Client Codes

as per P75xE

OPTION No DESCRIPTION

DEFAULT

P82E

ENABLE OPTIONS

Enable Dialler

[not used]

Enable Radio Interface
Enable Output Expander

3E
4E

ENablE OPTiONS

P82e 1e:

not used

P82e 2e: eNAbLe tHe DIALLer.

(on by default). this option can be used to disable the dialler while retaining all
dialler programming.

P82e 3e: eNAbLe rADIo INterfACe.

(off by default).

enables the optional 100-200 radio interface, (if used).

P82e 4e: eNAbLe oUtPUt exPANDer.

(off by default).

enables the optional 100-011 output expander, (if used).

the optional D24 output expander connects to the D24 control panel and
provides 35 open collector outputs and 1 relay output.

the outputs can be used to drive mimic displays, provide additional outputs on
alarm and various other custom purposes.

the output expander board interfaces with the D24 by three wire serial
connection. the board is designed to fit inside the D24 control panel housing.

P82e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

2E on: Dialler enabled
3E off: Radio Interface disabled
4E off: Output Expander disabled

tO prOgraM:
p82e

[Select option]

P80e, P81e

CreAte INStALLer DefINeD oUtPUt groUPS - metHoD 2

See page 25

for full details of output expander operation, see page 52.

heX aCCOunt nuMBer

if the Client account
numbers are required to be
sent in hex, use this table
when programming.

(hex a cannot be used).

Hex keypad

keypad

DIgIt

keY Display

VieW

arM 12

Monitor

area

F eXCluDe

Содержание D24





























































Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды

Ness D24, Инструкция по установке и программированию

Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды