Ness D24 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 60

background image

44

O P E r a T i O N

oP

neSS D24 Control Panel - inStallation & PrograMMing Manual

mONiTOr mOdE armiNg

Monitor mode allows you to arm selected zones while others are ignored. typically
used to monitor perimeter zones (doors and windows) while you are at home.

your system may be programmed to give the choice of arming two different Monitor
areas (Dual Monitor mode), otherwise there is one Monitor area (Single Monitor
mode).

ArmINg SINgLe moNItor moDe

Press...

...or

...or

[COde]

Three beeps will sound

and the MONITOR icon will flash constantly

ArmINg DUAL moNItor moDe

Press...

...or

...or

...or

MONITOR 1 armed is indicated by the

icon flashing constantly.

MONITOR 2 armed is indicated by the

icon flashing constantly.

ZOnes Must Be sealed

Make sure that all zones in the Monitor area

are sealed before Arming Monitor mode.

eXIt delaY

The Exit Delay time applies to Monitor
mode.

PaNiC alarm

the keypad panic function may have been programmed to be either:

Audible:

activates siren or buzzers, or

Silent:

if Central Station monitored, sends

a Panic report by dialler. (if Panic reports are enabled, P40xxe 6e).

Panic cannot be used while the panel is in Program, Memory or exclude mode.

Keypad Panic alarm is number

6

in the

SYSTEM

view.

Press...

(Press and hold for at least 1 second)

...or

(If Two Button Keypad Operation is enabled)

durESS alarm

a DureSS alarm can be triggered to alert the Central Monitoring Station that the
user is being forced to Disarm the panel against their will.

to Disarm and simultaneously send a DureSS alarm, prefix any valid user Code
with the “Duress Digit” when Disarming.

the factory default Duress Digit is 9. (it can be any number from 0–9).

By default, DureSS alarms do not sound any audible alarms, P40xxe 5e).

Duress alarm is number

5

in the

SYSTEM

view.

Disarm by pressing...

[duress dIgIt] [user Code]

The panel Disarms as normal and the Duress report is sent to the Central Monitoring Station.

• If DURESS alaRm IS

USeD, AVoID USer CoDeS

tHAt begIN WItH tHe SAme

NUmber AS A DUreSS DIgIt.

• DURESS alaRm can only

be USeD If tHe SYStem

IS CeNtrAL StAtIoN

moNItoreD.

«
...
42
43
44
45
46
...
»

Содержание D24





























































Отзывы:

Нет отзывов

Похожие инструкции для D24

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 8

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: V2 ELETTRONICA Страницы: 6

Бренд: Hach Страницы: 210

Бренд: janitza Страницы: 58

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 44

Бренд: Union Instruments Страницы: 63

Бренд: Watts Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды