Ness D24 Скачать руководство пользователя страница 30

Страница: 30 / 60

diallEr - PrOgrammiNg

D. Prog

neSS D24 Control Panel - inStallation & PrograMMing Manual

rEmOTE aCCESS OPTiONS

these options will enable the D24 to auto answer an incoming call and carry out
the functions as described.

See reMote oPeration By telePhone, page 51.

P58e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

none

tO prOgraM:
p58e

[Select option]

OPTION No DESCRIPTION

DEFAULT

P59E

Required Rings to Auto-answer

Enable upload/download with Callback

Enable upload/download with Fax Defeat
Enable remote ADMIN Arming

Send O/C reports with Client codes

as per P75xxE

Send only ADMIN AREA O/C reports

Enable Open/Close reports

Enable remote AREA 1 Arming

Disable Open/Close reports

Enable remote AREA 2 Arming

Enable remote AREA 3 Arming

Enable remote toggle AUX1 & AUX2

Enable remote Disarm all Areas

P58E

P60E

REMOTE ACCESS
OPTIONS

OPEN/CLOSE
REPORTING OPTIONS

5E
6E
7E
8E

rEQuirEd riNgS TO auTO-aNSwEr

this option sets the number of double rings before the D24 enables auto-
answering of the next call.

the number of rings can be set from 0 to 20 rings. 1 ring is recommended for fax
defeat to work correctly.

FaX deFeat

Fax Defeat works as follows:

1. Phone the D24 telephone number and listen for the required number of rings
(ring ring...ring ring) and then hang up.

2. Call the number again within 60 seconds.

3. the dialler will answer the very next incoming call on the first ring detected (this
may require one or two rings in practice).

if 60 seconds has expired before the next call, the dialler will revert back to the
count-ring mode as above.

P59e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

1 ring

tO prOgraM:
p59e

[required rings]

(Select 0 to 20 rings)

OPEN/ClOSE rEPOrTiNg OPTiONS

P60e 1e eNAbLe oPeN/CLoSe rePortS
P60e 2e SeND oNLY ADmIN AreA oPeN/CLoSe rePortS
P60e 3e SeND o/C rePortS WItH CLIeNt CoDeS AS Per P75xxe

this option enables the reporting of area open/close reports using the Client
numbers as programmed at options P751e, P752e, P753e.

P60e 4e DISAbLe oPeN/CLoSe rePortS

When this option is enabled, option 1e automatically disables.

if open/Close reports are disabled, the panel will send a ForCeD oPening
rePort if there has been an alarm during the armed period.

P60e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

1E on: Open/Close reports enabled

tO prOgraM:
p60e

[Select option]

Содержание D24





























































Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды

Ness D24, Инструкция по установке и программированию

Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды