Ness D24 Скачать руководство пользователя страница 13

Страница: 13 / 60

P r O g r a m m i N g

Prog

neSS D24 Control Panel - inStallation & PrograMMing Manual

FaCtOrY deFault
Master Code: [blank]

Installer Code: 000000

[INSTALLER CODE]

Factory default Installer Code: 000000

[MASTER CODE]

USER PROGRAM Mode

INSTALLER PROGRAM Mode

NORMAL OPERATING Mode

Power up with

J1 Link OFF

(Usually on first time installation)

PROGRAM LIGHT IS FLASHING

PROGRAM LIGHT IS ON

PROGRAM LIGHT IS OFF

PrOgram mOdE lEvElS

Installer Program mode

installer Program Mode allows
access to all program options.

Note: The panel will remain in Installer
Program Mode indefinitely.

PROGRAM

light

is FLASHING

User Program mode

user Program Mode allows the
owner to program:

• All User Codes
• Entry and Exit times

Note: The panel will automatically drop
out of User Program Mode to Operating
Mode if no keypad buttons are pressed
for 1 minute.

PROGRAM

light

is ON

HOw TO ENTEr PrOgram mOdE

from Power UP

1. Power-up with the J1 link oFF.

The J1 link must be ON in operating mode. (Or, if using J1 for housing tamper,
the tamper switch/es must be sealed).

UsIng the keyPad

the panel must be Disarmed.

1. Press

[MASTER CODE]

The keypad will respond with 3 beeps

This is User Program Mode (PROGRAM light is ON).

2. then press

[INSTALLER CODE]

The keypad will respond with 3 beeps

This is Installer Program Mode (PROGRAM light is FLASHING).

HOw TO EXiT PrOgram mOdE

1. Press then

this is operating Mode (PrograM light is oFF).

key seqUence In Program mode

3 beeps

Selects a program

option (address)

The current value

is displayed

The keypad lights or

icons will display the

current value

Enter new

data

3 beeps

2-4 digit Option No.

Enter

new value

tHe PANeL WILL Not exIt
ProgrAm moDe UNLeSS
USer CoDe 1 (P1e) IS
ProgrAmmeD.

Содержание D24





























































Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды

Ness D24, Инструкция по установке и программированию

Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды