Ness D24 Скачать руководство пользователя страница 34

Страница: 34 / 60

diallEr - PrOgrammiNg

D. Prog

neSS D24 Control Panel - inStallation & PrograMMing Manual

OPTION No DESCRIPTION

DEFAULT

P72E
P73E
P74E

Enable Easycall feature
Digits to dial after Opening
Digits to dial after Closing

OFF

0 (disabled)
0 (disabled)

EaSyCall dialliNg

the D24 can dial pre-programmed digits after opening and closing reports. this
can be used to automatically enable and disable easycall telephone diversion of
the premises telephone every time the panel is armed and Disarmed.

P72e eNAbLe eASYCALL feAtUre

Press P72e 1e to enable/disable the option. the option is off by default.

P73e DIgItS to DIAL After oPeNINg

Press P73e [digits] e

normally, you would want to disable easycall diversion after opening, ie., the
client is now at home.

example:

the digits #21# will be dialled after the panel has sent the opening report (if
enabled).

P74e DIgItS to DIAL After CLoSINg

Press P74e [digits] e

Program the telephone number to divert to.

example:

[telephone number]

the digits *21 [telephone number] # will be dialled after the panel has sent the
Closing report (if enabled).

P72e, P73e, P74e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

Easycall disabled

tO prOgraM:

p72e 1e

toggles the option ON and OFF

p73e

[digits]

(Up to 15 digits to dial)

p74e

[digits]

(Up to 15 digits to dial)

nOtes:

The digits programmed at P73E and P74E are

not dependant on Open/Close reports. If Open/

Close reports are disabled, the digits will be

dialled after Arming/Disarming.

sPecIal characters (applies to all telephone numbers)

Pauses, * (star) or # (hash) (VF digits) can be included in the dialling
sequence by using the keys in the table below.

sPecIal character

key entry

IndIcatIon on lcd dIsPlay

PauSe (1.6sec)

area Key

6 (Flashing)

* (Star)

arM Key

2 (Flashing)

# (hash)

Monitor Key

3 (Flashing)

sPecIal characters for telePhone nUmbers

Содержание D24





























































Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды

Ness D24, Инструкция по установке и программированию

Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды