Ness D24 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 60

background image

39

N E S S r a d i O

neSS D24 Control Panel - inStallation & PrograMMing Manual

OPTION No

DESCRIPTION

DEFAULT

P93E

Medical Delay

0 hours

mEdiCal dElay

any 24 hour zone or Key switch input or Panic input may be used to control
Medical alarm by assigning the chosen input to output group 16.

A.

instant Medical alarm: immediately sound the sirens and send a Medical alarm

report to the Central Monitoring Station. (the Medical alarm Delay must be set at
zero hours).

b.

inactivity Medical alarm: the Medical alarm is reported if the Medical alarm

button is not pressed within the pre-programmed Medical alarm Delay. (the
Medical alarm Delay can be set between 1 and 48 hours).

INStANt meDICAL ALArm - oPerAtIoN

1. if the Medical alarm Delay is not being used, simply press the designated
Medical alarm button.

2. if the Medical alarm Delay is being used, an instant Medical alarm can be sent
by pressing the button twice within 12 seconds. on the first press, the keypad/s
will beep once per second during the 12 second period. on the second press, the
keypad/s will beep fast to indicate that the Medical alarm has been reported.

INACtIVItY meDICAL ALArm - oPerAtIoN

the inactivity Medical alarm can be used to summon assistance if a person has
become incapacitated and is not able to press their Medical alarm button.

For example, if the Medical alarm Delay is set for 24 hours, the Medical alarm will
be triggered if the button is not pressed every 24 hours.

When 20 minutes of the Medical alarm Delay time remains, and the Medical
alarm button has not been pressed, the keypad/s will beep for 10 seconds as a
reminder.

as a final warning that the Medical alarm delay is due to expire, the keypad/s will
beep continuously during the final 10 minutes.

P93e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

0 hours (disabled)

tO prOgraM:

p86e

[0-48 hours]

e

related OptIOns:

P40xxE 7E To map the Medical Alarm to an

Output Group. Default is Output Group 30
(So dialler). See page 23.

Medical Alarm Operation, page 45.

«
...
37
38
39
40
41
...
»

Содержание D24





























































Отзывы:

Нет отзывов

Похожие инструкции для D24

Бренд: FAAC Страницы: 12

Бренд: C&K systems Страницы: 2

Бренд: Lawler Страницы: 4

Бренд: Universal Remote Страницы: 20

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

Бренд: ACL Страницы: 20

Бренд: Apex Toys Страницы: 7

Бренд: Fluidmaster Страницы: 2

Бренд: EVERSPRING Страницы: 3

Бренд: elsner elektronik Страницы: 2

769N FireLock NXT Series

Бренд: Victaulic Страницы: 40

Infi 90 IMSPM01

Бренд: Bailey Страницы: 52

Бренд: Anthem Страницы: 8

Бренд: National Instruments Страницы: 11

Бренд: Victaulic Страницы: 2

VEGACAP 60 Series

Бренд: Vega Страницы: 12

Бренд: D+H Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды