Ness D24 Скачать руководство пользователя страница 32

Страница: 32 / 60

diallEr - PrOgrammiNg

D. Prog

neSS D24 Control Panel - inStallation & PrograMMing Manual

OPTION No DESCRIPTION

DEFAULT

P65E

P66E

MULTIPLE ALARM
REPORTING

RESTORALS
REPORTING

Disable reporting multiple zone alarms

Send Restorals on Disarm

Enable reporting multiple zone alarms

Send Restorals immediately

Send Restorals after Siren Time

Do not send Restorals

mulTiPlE alarm rEPOrTiNg

By default, the panel will report zone alarms once per arming cycle.

P65e 1e and 2e will toggle the selection of ‘single hit’ and ‘multibreak’ reporting.

P65e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

Multiple reporting disabled

tO prOgraM:
p65e 1e

to disable multiple alarm reporting

p65e 2e

to enable multiple alarm reporting

rESTOralS rEPOrTiNg

these options apply only to zone alarms.

all other alarm types send restorals when they happen, except for Duress, Panic,
access Code and Medical for which a restoral is never sent.

P66e 1e SeND reStorALS After SIreN tIme

the restoral is sent when Siren time (P28e) has expired and the input has
resealed.

P66e 2e SeND reStorALS oN DISArm

the restoral is sent when the panel is next Disarmed, provided the input has
resealed.

P66e 3e SeND reStorALS ImmeDIAteLY

the restoral is sent immediately the input has resealed.

P66e 4e Do Not SeND reStorALS

this option disables the reporting of zone restorals.

P66e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

3E on: Restorals sent immediately

tO prOgraM:
p66e

[Select option]

OPTION No

DESCRIPTION

DEFAULT

P67E

Mains Fail reporting delay

60 minutes

maiNS fail rEPOrTiNg dElay

this option sets the time, in minutes, for reporting of Mains power failure to be
delayed. this prevents the unecessary reporting of brief power interruptions.

the delay time can be programmed from 0–255 minutes.

Mains Power Failure is enabled and configured as an alarm by the related option
P41xxe 1e.

P67e

prOgraM MOde leVel:

Installer, Remote by PC

FaCtOrY deFault:

60 minutes

tO prOgraM:
p67e

[time]

(Select 0–255 minutes)

related OptIOns:

P41E xxE, Mapping power alarms, page 23

Содержание D24





























































Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды

Ness D24, Инструкция по установке и программированию

Результаты поиска

Содержание D24

Отзывы:

Похожие инструкции для D24

Бренды по названию

Популярные бренды