Ness D24, Инструкция по установке и программированию

Страница: 14 / 60

14
P r O g r a m m i N g
Prog
neSS D24 Control Panel - inStallation & PrograMMing Manual
uSEr COdES 1–30
user codes are the P.i.n. codes used to operate various panel functions,
especially arming and Disarming. there are 30 user Codes and each can be 3 to
6 digits long.
user Code 1 is always a MaSter CoDe.
user Codes 2 to 30 can be programmed as one of the types: orDinary,
aDMiniStrator, area or MaSter.
When programming codes, the user Code type is indicated by the icons:
ARM
if user Code 1 was used to enter Program Mode, the digits of any existing codes
will be displayed when programming a user Code.
OrdInarY COde & adMInIstratOr COde
an ordinary Code is for systems configured without areas. allows full access to
the panel except for entry to Program Mode.
(When the panel is partitioned this
code is called the Administrator Code).
an administrator Code is able to arm and Disarm all areas of a Partitioned system,
but it is not allowed entry to Program Mode.
To Program an Ordinary Code or Admin Code: [OptIOn] [COde] [COde]
The
ARM
icons will be ON.
area COde
an area Code is a code which only has access to the area assigned to it.
To Program: [OptIOn] [area no.] [COde] [COde]
One of the icons or or will be ON, depending on [Area No.] entered.
Master COde
a Master Code is able to arm and Disarm all areas of a Partitioned system and
is allowed entry to Program Mode. user Code 1 is always a Master Code, but all
other codes can be programmed as Master Codes if needed.
To Program: [OptIOn] 0 [COde] [COde]
The
ARM
icons will be FLASHING.
eXaMples:
Program user Code 1, the permanent Master Code, to be 1234: P1e 1234e 1234e
Program user Code 2 to be 789 and an Ordinary Code : P2e 789e 789e
Program user Code 3 to be 5678 and an Area 1 Code : P3e 1e 5678e 5678e
Program user Code 4 to be 222 and an Area 2 Code : P4e 2e 222e 222e
Program user Code 5 to be 8990 and an Area 3 Code : P5e 3e 8990e 8990e
P1e – P030e
prOgraM MOde leVel:
User, Installer, Remote by PC
FaCtOrY deFault:
[blank]
tO prOgraM:
p
[Option No] e [new code] e [new code] e
nOtes:
• User Codes can be 3 to 6 digits in length.
• User codes cannot start with ‘0’.
• All codes must be unique to each other.
• The panel is supplied with NO user codes
programmed.
• To delete a code, re-program the code as 000.
e.g, To Delete User Code 2: P2E 000E 000E
• To clear all codes, enter P982E in Installer
Program mode. See Page 41.
• Codes are rejected if already used. Some
codes that are similar to existing codes may
also be rejected.
• Open/Close reports are identified by user
number when the control panel is central
station monitored.
related OptIOns:
Program Installer Code, page 40
USER CODE DEFAULT
User Code 1 (Master Code)
User Code 2
User Code 3
User Code 4
User Code 5
User Code 6
User Code 7
User Code 8
User Code 9
User Code 10
User Code 11
User Code 12
User Code 13
User Code 14
User Code 15
User Code 16
User Code 17
User Code 18
User Code 19
User Code 20
User Code 21
User Code 22
User Code 23
User Code 24
User Code 25
User Code 26
User Code 27
User Code 28
User Code 29
User Code 30
OPTION No
P1E
P2E
P3E
P4E
P5E
P6E
P7E
P8E
P9E
P10E
P11E
P12E
P13E
P14E
P15E
P16E
P017E
P018E
P019E
P020E
P021E
P022E
P023E
P024E
P025E
P026E
P027E
P028E
P029E
P030E
prOgraMMIng FeedBaCK
When programming user codes, the existing code and then the new code is ‘read back’ by flashing the
numeric keypad icons 0–9.
1. Press: p [Option no] e the existing code is displayed by the keypad.
2. Enter the new code (3 to 6 digits): [new code] e
3. Enter the new code again: [new code] e , the new code will be displayed.
NOTe: After step 1, the new code can be entered immediately without waiting for the display to finish the ‘read back’.