Ness D24 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 60

background image

45

O P E r a T i O N

oP

neSS D24 Control Panel - inStallation & PrograMMing Manual

mEdiCal alarm

your system may have been setup with a Medical alarm. this type of alarm can be
used to summon assistance for the elderly or infirm who are living alone. a Medical
alarm is most effective if the system is monitored by a Central Monitoring Station.

Medical alarms can be used in two ways:

1. inStant MeDiCal alarM: immediately sound the sirens and send a Medical
alarm report to the Central Monitoring Station. (in this case, the Medical alarm Delay
is set at zero hours).

2. inaCtiVity MeDiCal alarM: the Medical alarm is reported if the Medical alarm
button is not pressed within the pre-programmed

Medical Alarm Delay.

(in this case,

the Medical alarm Delay is set between 1 and 24 hours).

Instant medIcal alarm

oPeratIon

1. if the Medical alarm Delay is not being used, simply press the designated Medical
alarm button.

2. if the Medical alarm Delay

is

being used, an instant Medical alarm can be sent by

pressing the button twice within 12 seconds. on the first press, the keypad/s will beep
once per second during the 12 second period. on the second press, the keypad/s
will beep fast to indicate that the Medical alarm has been reported.

InactIvIty medIcal alarm

oPeratIon

the inactivity Medical alarm can be used to summon assistance if a person has
become incapacitated and is not able to press their Medical alarm button.

For example, if the Medical alarm Delay is set for 24 hours, the Medical alarm will
be triggered if the button is not pressed every 24 hours. (effectively, it is an, “i’m
oK”, button).

When 20 minutes of the Medical alarm Delay time remains, and the Medical
alarm button has

not

been pressed, the keypad/s will beep for 10 seconds as a

reminder.

as a final warning that the Medical alarm delay is due to expire, the keypad/s will
beep continuously during the final 10 minutes.

medIcal alarm bUtton

the Medical alarm button can be setup to take the place of the keypad Panic button
or it may be a separate button. this must be determined by your installer.

Medical alarm is number

7

in the

SYSTEM

view.

firE alarm

your system may have smoke detectors connected to 24 hour Fire inputs.

Fire inputs, (if enabled), are indicated by the Fire

icon on the keypad.

any zone can be become a Fire input by mapping it to output group 26.

this page is an extract from the
D24 user Manual.

See Page 39 for Medical Delay
programming.

Note:

if inactivity Medical alarm is
enabled, the client should
give notice to their monitoring
station if they plan to be
absent from the premises for
extended periods, (holidays,
visits etc).

«
...
43
44
45
46
47
...
»

Содержание D24





























































Отзывы:

Нет отзывов

Похожие инструкции для D24

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Бренд: FAAC Страницы: 16

PXI-6683 Series

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 29

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 7

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 21

FieldPoint FP-1001

Бренд: National Instruments Страницы: 65

FieldPoint FP-1001

Бренд: National Instruments Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды