Mita ADIABATIC PAD-V Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 62

background image

MITA-PAD-V-MAN-IT-
201812

© MITA Cooling Technologies
S.r.l.

28 / 59

4

Transport, handling and positioning

PAD-V

INSTRUCTION
MANUAL

4

TRANSPORT, HANDLING AND POSITIONING

4.1 General warnings

It is assumed, for the safe use of the machine, that the reader of this chapter is already familiar with the
contents of heading 2 "Safety".

The following paragraphs provide details on the specific requirements for safely interacting with the machine.

Operating personnel:

MAINTENANCE MECHANIC

MAINTENANCE ELECTRICIAN

SKILLED TECHNICIAN - MITA Cooling Technologies S.r.l.

CAUTION

Handling, loading and unloading of the machine must be carried out by qualified personnel
who are familiar with the contents of this manual.

CAUTION

Make sure there are no unauthorised persons in the area where the machine is to be loaded/
unloaded from the means of transport.

CAUTION

During operations, the operator must wear all the necessary Personal Protective Equipment
(PPE) based on the particular stage in the machine's life cycle. See heading 2, "Safety".

IMPORTANT

The Manufacturer declines all liability for operations performed:

• by inadequate personnel;

• without observing the health and safety regulations in force;

• without observing the procedures provided in these instructions.

WARNING

Before proceeding with any type of procedure, it is essential to have read and understood
the contents of this manual, studied the relative images and adopted the safety and
protection measures described.

«
...
28
29
30
31
32
...
»

Содержание ADIABATIC PAD-V































































Отзывы:

Нет отзывов

Похожие инструкции для ADIABATIC PAD-V

Бренд: LAZER Страницы: 13

Бренд: Latento Страницы: 60

Бренд: Easy Quick Страницы: 11

Бренд: Radio Shack Страницы: 2

Бренд: omnicharge Страницы: 12

Бренд: omnicharge Страницы: 72

Бренд: NEC Страницы: 2

Бренд: Bartington Страницы: 11

Бренд: Fantasea Страницы: 18

Бренд: Fantasea Страницы: 15

Бренд: Oben Страницы: 12

Бренд: OBH Nordica Страницы: 20

Бренд: Wahoo Страницы: 2

BMP 01-ZLZPP 1A 00-P S75 Series

Бренд: Balluff Страницы: 20

Бренд: Yeti Страницы: 19

Бренд: veba Страницы: 11

Бренд: DAVIS Страницы: 32

Zerolite Wheelset

Бренд: Vuelta Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды