Mita ADIABATIC PAD-V Скачать руководство пользователя страница 56

Страница: 56 / 62

Maintenance

PAD-V

INSTRUCTION
MANUAL

MITA-PAD-V-MAN-IT-
201812

54 / 59

Problem

Action needed to find probable

cause

Solution

No cooling (increase in the
water temperature in the
circuit).

Check that the liquid flow rate in
the primary circuit meets the
design parameters

Adjust flow rate

Make sure fans are efficient and
check the direction the air flows
through the cooler

Cut the power to the electric fan
and invert two of the three
phases in the power line

Check that there is no recycling
of air from the fan outlet to the
side inlets.

Contact the Technical Office of

MITA Cooling Technologies
S.r.l.

Check that no hot air is being
drawn in from other sources

Contact the Technical Office of

MITA Cooling Technologies
S.r.l.

Check the condition of the
humidifier pack, making sure it is
not damaged, clogged or scaled
up.

Replace the humidifier pack

Check that the heat exchange
battery (fins or tubes) is not
scaled up.

Contact the Technical Office of

MITA Cooling Technologies
S.r.l.

Vibration and/or noise

Check that the cooler is installed
on  a  flat  surface  and  therefore
that  the  axis  of  the  motor  is
perpendicular  to  the  ground  (if
this  is  not  the  case,  fan
imbalance occurs)

Level the cooler

Check the correct tightening of
the fan to the body of the
machine

Cut power to the fan and check
tightness of all screws

Fan blades broken

or off-balance

Contact MITA Cooling
Technologies S.r.l. Technical
Office

Table 6

– Troubleshooting

Содержание ADIABATIC PAD-V































































Результаты поиска

Содержание ADIABATIC PAD-V

Отзывы:

Похожие инструкции для ADIABATIC PAD-V

Бренды по названию

Популярные бренды

Mita ADIABATIC PAD-V, Инструкция по эксплуатации

Результаты поиска

Содержание ADIABATIC PAD-V

Отзывы:

Похожие инструкции для ADIABATIC PAD-V

Бренды по названию

Популярные бренды