Mita ADIABATIC PAD-V Скачать руководство пользователя страница 55

Страница: 55 / 62

PAD-V

Maintenance

INSTRUCTION
MANUAL

MITA-PAD-V-MAN-IT-
201812

53 / 59

8.5 Troubleshooting

Fault

Action needed to find probable cause

Solution

Electric fan absorbs too
much electricity

Check the direction the air is flowing
through the cooler (direction of rotation
of the fan)

Cut the power to the electric fan
and invert two of the three
phases in the power line

Obstruction on the air intake and output
sections

Remove obstructions if possible

Check  the  ambient  air  temperature  (if
the  ambient  air  is  too  cold,  the  motor
may  absorb  more  than  the  rated
amount)

Contact the Technical Office of

MITA Cooling Technologies
S.r.l..

Check that the gaps between the fins
and the pipes in the heat exchange
battery are not scaled up or clogged.

Contact the Technical Office of

MITA Cooling Technologies
S.r.l.

Water drawn

outside the unit

Check the correct distribution of the
water on the humidifier pack

Clean the distribution tanks, or
contact the technical office of
MITA Cooling Technologies
S.r.l..

Check that the heat exchange battery is
not partially clogged or scaled up.

Contact the Technical Office of

MITA Cooling Technologies
S.r.l.

Water leaking from
the tank and/or
Overflow drain -
panel alarm signal

Check the correct operation of the
water loading solenoid valve (that it is
not locked in the ON position)

Release the valve. Contact the
MITA

Cooling

Technologies

S.r.l. Technical Office

Check for any obstructions

Remove obstruction

Содержание ADIABATIC PAD-V































































Результаты поиска

Содержание ADIABATIC PAD-V

Отзывы:

Похожие инструкции для ADIABATIC PAD-V

Бренды по названию

Популярные бренды

Mita ADIABATIC PAD-V, Инструкция по эксплуатации

Результаты поиска

Содержание ADIABATIC PAD-V

Отзывы:

Похожие инструкции для ADIABATIC PAD-V

Бренды по названию

Популярные бренды