Mita ADIABATIC PAD-V Скачать руководство пользователя страница 54

Страница: 54 / 62

Maintenance

PAD-V

INSTRUCTION
MANUAL

MITA-PAD-V-MAN-IT-
201812

52 / 59

8.3.9 Wetting Pump Maintenance

It is advisable to periodically check:

•  The condition of the cables and cable glands, especially at attachment points.
•  Wear of the impeller as this will negatively affect performance.
•  Cleanliness of the suction area.

Using the pump where the water is hard or very sandy may shorten the life of the mechanical seal.

8.4 Extraordinary maintenance

For any extraordinary maintenance work not described in this manual, turn to technicians specifically
appointed by MITA Cooling Technologies S.r.l.

CAUTION

MITA Cooling Technologies S.r.l. shall not be held responsible for maintenance carried out by
personnel it has not directly appointed.

Содержание ADIABATIC PAD-V































































Результаты поиска

Содержание ADIABATIC PAD-V

Отзывы:

Похожие инструкции для ADIABATIC PAD-V

Бренды по названию

Популярные бренды

Mita ADIABATIC PAD-V, Инструкция по эксплуатации

Результаты поиска

Содержание ADIABATIC PAD-V

Отзывы:

Похожие инструкции для ADIABATIC PAD-V

Бренды по названию

Популярные бренды