Hotline: +49 5251 688865-99
Hotline: +49 5251 688865-99
Hotline: +49 5251 688865-99
Hotline: +49 5251 688865-99
Hotline: +49 5251 688865-99
. Operating Manual grandMA Version 5.4
93
93
93
93
93
4 . 3 . 2
4 . 3 . 2
4 . 3 . 2
4 . 3 . 2
4 . 3 . 2 Changing the TRIGGER (Call-up) of individual Cues within a Sequence
Changing the TRIGGER (Call-up) of individual Cues within a Sequence
Changing the TRIGGER (Call-up) of individual Cues within a Sequence
Changing the TRIGGER (Call-up) of individual Cues within a Sequence
Changing the TRIGGER (Call-up) of individual Cues within a Sequence
Select the respective cue within the Trig column (red cell).
Enter the following with the left Encoder or via the keyboard and confirm with ENTER.
-
F: for FOLLOW mode
-
G: for GO button
-
S: for SOUND signal
-
No.: Automatically according to set time (e.g. if the set time is 1.5, this Cue will be called up after 1.5 seconds
automatically).
4 . 3 . 3
4 . 3 . 3
4 . 3 . 3
4 . 3 . 3
4 . 3 . 3 Changing the FADE or DELA
Changing the FADE or DELA
Changing the FADE or DELA
Changing the FADE or DELA
Changing the FADE or DELAY times of individual steps within the
Y times of individual steps within the
Y times of individual steps within the
Y times of individual steps within the
Y times of individual steps within the
Sequence
Sequence
Sequence
Sequence
Sequence
Select the respective cue (red cell).
Here, the duration for
this
this
this
this
this
cue can be changed with the In-Fade, In Delay or Snap encoder.
Pressing the
Basics
Basics
Basics
Basics
Basics
button (above the right Encoder) will switch this button to
Out
Out
Out
Out
Out
: Now, you can modify
this time with the Encoder Out-Fade.
If no FADE or DELAY times are indicated, none are stored in this CUE.
Changing all times of one or more Cues ( CUE TIME SCALING )Changing all times of one or more Cues (
CUE TIME SCALING )
With this function, you can scale or compress all Fade, Delay, and Trigger times.
select one ore more Cues (red cell).
click on the Cue’s number using the right mouse button or the Encoder on the side of the monitor, der
rechten Maustaste oder dem Encoder neben dem Monitor
In the EDIT CUE NUMBER menu, select a percentage or absolute change
- Scale Timing (%): All times of the marked Cue will be changed to the entered value.When entering
100%, all values remain unchanged.
- Scale Timing (sec): The total time of the marked Cues will be changed to the entered time – all times
will change proportionally. For the example on the left: For the 4 marked Cues, 6 seconds were entered;
DELAY and FADE were increased to 6 seconds in total; the trigger time increases according to the
proportional changes of the individual times.
Use the Calculator to make the changes, and confirm with ENTER.
WARNING: If you compress all times to 0, you will no longer be able to enter longer times. You would then have
to enter all times anew, or you could restore them, if the OOPS function was activated (not on the
MICRO).
FADE times in Profiles
Besides lineary FADE times, you can also use to vary FADE procedures using a profile. You can fade dimmers and
PAN/TILT movements using individual profiles. In this version, it is irrelevant whether the PATH column contains no
entry or „linear“. You can choose from 43 paths, 16 of which are pre-defined, and 16 that you can assign self-
