Lenovo HX3510-G Скачать руководство пользователя страница 431

Страница: 431 / 1240

•

800b0008-1301ffff : Redundancy [RedundancySetElementName] has been restored. (Power Unit)

This message is for the use case when an implementation has detected Redundancy was Restored.

May also be shown as 800b00081301ffff or 0x800b00081301ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Redundant Power Supply

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0561

User Response

No action; information only.

•

800b0108-1301ffff : Redundancy Lost for [RedundancySetElementName] has asserted. (Power

Unit)

This message is for the use case when Redundancy Lost has asserted.

May also be shown as 800b01081301ffff or 0x800b01081301ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Redundant Power Supply

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0802

User Response

1. Check the LEDs for both power supplies.

2. Follow the actions in Power-supply LEDs.

Appendix A. Integrated management module II (IMM2) error messages

419

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды