Lenovo HX3510-G Скачать руководство пользователя страница 231

Страница: 231 / 1240

• Do not set down the heat sink after you remove the plastic cover.

• Do not touch the thermal grease on the bottom of the heat sink after you remove the plastic

cover. Touching the thermal grease will contaminate it. See “Thermal grease” on page 221
for more information.

Heat sink

Thermal grease

Flange

Figure 184. Thermal grease

Remove the plastic protective cover from the bottom of the heat sink.

Grasp the heat sink firmly as the following illustration to avoid possible damage to the heat sink.

Figure 185. Heat sink

Position the heat sink over the microprocessor. The heat sink is keyed to assist with proper
alignment.

Chapter 5

Removing, and replacing components

219

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды