Lenovo HX3510-G Скачать руководство пользователя страница 1049

Страница: 1049 / 1240

•

S.3030007 A firmware fault has been detected in the UEFI image. Internal UEFI Firmware Fault

Detected, System halted

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check IBM support site for an applicable service bulletin or firmware update that applies to

this error.

Update the UEFI image.

Replace the system board.

•

S.3040007 A firmware fault has been detected in the UEFI image. Internal UEFI Firmware Fault

Detected, System halted

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check IBM support site for an applicable service bulletin or firmware update that applies to

this error.

Update the UEFI image.

Replace the system board.

•

S.3050007 A firmware fault has been detected in the UEFI image. Internal UEFI Firmware Fault

Detected, System halted

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check IBM support site for an applicable service bulletin or firmware update that applies to

this error.

Update the UEFI image.

Replace the system board.

•

S.3058004 A Three Strike boot failure has occurred. The system has booted with default UEFI

settings. POST failure has occurred! System booted with default settings.

Explanation:

Appendix B. UEFI/POST diagnostic codes

1037

«
...
1047
1048
1049
1050
1051
...
»

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды