Lenovo HX3510-G Скачать руководство пользователя страница 44

Страница: 44 / 1240

The server can be turned off in any of the following ways:

• You can turn off the server from the operating system, if your operating system supports this feature. After

an orderly shutdown of the operating system, the server will turn off automatically.

• You can press the power-control button to start an orderly shutdown of the operating system and turn off

the server, if your operating system supports this feature.

• If the operating system stops functioning, you can press and hold the power-control button for more

than 4 seconds to turn off the server.

• The server can be turned off by Wake on LAN feature with the following limitation:

Note:

When you install any PCI adapter, the power cords must be disconnected from the power source

before you remove the PCI Express riser-card assembly. Otherwise, the Wake on LAN feature might not
work.

• The IMM2 can turn off the server as an automatic response to a critical system failure.

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды