Lenovo HX3510-G Скачать руководство пользователя страница 315

Страница: 315 / 1240

Minimum Power Cap exceeds Power Cap recovered

May also be shown as 4000008300000000 or 0x4000008300000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Power

SNMP Trap ID

164

CIM Information

Prefix:

IMM

ID:

0131

User Response

Information only; no action is required.

•

40000084-00000000 : IMM firmware mismatch between nodes [arg1] and [arg2]. Please attempt to

flash the IMM firmware to the same level on all nodes.

A mismatch of IMM firmware has been detected between nodes

May also be shown as 4000008400000000 or 0x4000008400000000

Severity

Error

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0132

User Response

Attempt to flash the IMM firmware to the same level on all nodes.

•

40000085-00000000 : FPGA firmware mismatch between nodes [arg1] and [arg2]. Please attempt

to flash the FPGA firmware to the same level on all nodes.

A mismatch of FPGA firmware has been detected between nodes

Appendix A. Integrated management module II (IMM2) error messages

303

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды