Lenovo HX3510-G Скачать руководство пользователя страница 1101

Страница: 1101 / 1240

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-903-000 : IANet:Interrupts Test Failed

A failure was detected during the Interrupt test.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. Check interrupt assignments in the PCI Hardware section of the DSA Diagnostic Log. If the

ethernet device is sharing interrupts, if possible modify the interrupt assignments using F1
Setup to assign a unique interrupt to the device.

4. Rerun the test.

5. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-904-000 : IANet:Loopback Test Failed

A failure was detected during the Loopback test.

Recoverable

Severity

Error

Serviceable

Appendix C. DSA diagnostic test results

1089

«
...
1099
1100
1101
1102
1103
...
»

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды