Lenovo HX3510-G Скачать руководство пользователя страница 799

Страница: 799 / 1240

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0525

User Response

No action; information only.

•

81070301-2c01ffff : Sensor [SensorElementName] has deasserted the transition to non-recoverable

from a less severe state. (ML2 OverTemp)

This message is for the use case when an implementation has detected that the Sensor transition to
non-recoverable from less severe has deasserted.

May also be shown as 810703012c01ffff or 0x810703012c01ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0525

User Response

No action; information only.

•

8107030d-2582ffff : Sensor [SensorElementName] has deasserted the transition to non-recoverable

from a less severe state. (RAID Vol State)

This message is for the use case when an implementation has detected that the Sensor transition to
non-recoverable from less severe has deasserted.

May also be shown as 8107030d2582ffff or 0x8107030d2582ffff

Appendix A. Integrated management module II (IMM2) error messages

787

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды