Kubota ME8200DTN Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 192

background image

ME8200DTN, WSM

BRAKES

N5-S3

3. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

Brake Pedal Free Travel

A

Stop the engine and remove the key, then choke the wheel
before checking brake pedal.

1. Release the parking brake.
2. Slightly depress the brake pedals and measure free travel (A)

at top of pedal stroke.

3. If the measurement is not within the factory specifications,

loosen the lock nut (1) and turn the turnbuckle (2) to adjust the
rod length within acceptable limits.

A

Keep the free travel in the right and left brake pedals
equal.

Parking Brake Lever Free Play

A

Stop the engine and chock the wheels before checking
parking brake.

1. Release the parking brake lever (1).
2. Loosen the lock nut (2) on the parking brake rod (3).
3. Adjust the parking brake rod length to achieve the reference

value.

4. Tighten the lock nut (2).
5. Pull the parking brake lever (1) just one notch and make sure

the parking brake shaft (5) is activated.

A

After adjusting the parking brake lever free play
- Right and left parking brake for even braking.
- With the parking brake released, make sure that the right
and lefet tires do not drag on.

Brake pedal free travel
(A)

Factory spec.

40 to 45 mm
1.6 to 1.8 in.

(1)

Lock Nut

(2)

Turnbuckle

0000003511E

Parking brake rod length
(L)

Reference value

180 to 184 mm
7.09 to 7.25 in.

(1)

Parking Brake Lever

(5)

Parking Brake Shaft

(2)

Lock Nut

A :

PULL

(3)

Parking Brake Rod

B :

RELEASE

(4)

Brake Lever

0000003512E

KiSC issued 04, 2006 A

«
...
118
119
120
121
122
...
»

Содержание ME8200DTN

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ME8200DTN

4400 BROCHURE 74-101

Бренд: MASSEY FERGUSON Страницы: 20

Бренд: Kubota Страницы: 370

Бренд: Zetor Страницы: 134

Бренд: Winton Страницы: 40

Бренд: Grouser Products Страницы: 28

Бренд: ASY Страницы: 117

Бренд: Land Pride Страницы: 76

Бренд: Jenn-Air Страницы: 28

ROBOPOWER 111300001

Бренд: McConnel Страницы: 96

Бренд: Husqvarna Страницы: 60

Бренд: Husqvarna Страницы: 36

Бренд: Husqvarna Страницы: 112

Бренд: Wallenstein Страницы: 28

Бренд: IMC Страницы: 22

Бренд: IMC Страницы: 24

Бренд: Gram Страницы: 48

Бренд: Belson Outdoors Страницы: 9

Бренд: ASP Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды