Kubota ME8200DTN Скачать руководство пользователя страница 122

Страница: 122 / 192

ME8200DTN, WSM

BRAKES

N5-S5

Brake Cam and Brake Cam Lever

1. Remove the external snap ring (1).
2. Remove the brake cam (2) and brake cam lever (4).

(When reassembling)

Apply grease to the O-ring (3) and take care not to damage the
O-ring.

Install the brake cam (2) to brake cam lever, aligning the
marks on them.

[3] SERVICING

Cam Plate Flatness

1. Place the cam plate on the surface plate.
2. Measure the flatness of cam plate with a feeler gauge at four

points on a diagonal line.

3. If the measurement exceeds the allowable limit, replace it.

Height of Cam Plate and Ball

1. Measure the dimensions of the cam plate with the ball

installed.

2. If the measurement is less than the allowable limit, replace the

cam plate and balls.

3. Inspect the ball holes of cam plate for uneven wear. If the

uneven wear is found, replace it.

(1)

External Snap Ring

(3)

O-ring

(2)

Brake Cam

(4)

Brake Cam Lever

0000003516E

Cam plate flatness

Allowable limit

0.3 mm
0.012 in.

0000002449E

Height of cam plate and
ball

Factory spec.

22.45 to 22.55 mm
0.8839 to 0.8879 in.

Allowable limit

22.00 mm
0.8661 in.

0000003518E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды