Kubota ME8200DTN Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 192

background image

ME8200DTN, WSM

FRONT AXLE

N6-S6

Front Wheel and Front Axle

1. Check the front axle and engine are securely mounted on the

disassembly stand.

2. Loosen the front wheel mounting nuts.
3. Lift the front axle and remove the front wheels.
4. Disconnect the 4WD / Bi-speed turn connector (1).
5. Remove the bracket (front) mounting screws and nuts.
6. Remove the bracket (rear) mounting screws and nuts.
7. Separate the front axle from front axle bracket.

(When reassembling)

A

Connect the power steering hose 1 with green tape to the RH.

A

Be sure to adjust the front axle rocking force.

(2) Disassembling Front Axle

Tie-rod

1. Pull out the cotter pin and loosen the tie-rod end slotted nut.
2. Disconnect the tie-rod with a tie-rod end lifter (Code No.

07909-39051).

(When reassembling)

A

After tightening the tie-rod end nut to the specified torques,
install a cotter pin as shown in the figure.

Tightening torque

Front wheel mounting
nut

166.7 to 196.1

17.0 to 20.0

122.9 to 144.6 ft-lbs

Bracket mounting nut

77.5 to 90.2

7.9 to 9.2

57.1 to 66.5 ft-lbs

(1)

4WD / Bi-speed Turn

Connector

0000003528E

Tightening torque

Tie-rod end slotted nut

77.5 to 90.2

7.9 to 9.2

57.1 to 66.5 ft-lbs

0000001898E

KiSC issued 04, 2006 A

«
...
131
132
133
134
135
...
»

Содержание ME8200DTN

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ME8200DTN

HiTech T Series

Бренд: Valtra Страницы: 31

Бренд: Sears Страницы: 24

Бренд: Hyundai Страницы: 46

Бренд: GOLDONI Страницы: 98

Бренд: satoh Страницы: 72

Бренд: New Holland Страницы: 41

FFC PREPARATOR LAF3566

Бренд: paladin Страницы: 31

Бренд: IMC Страницы: 13

ROBOPOWER 111300001

Бренд: McConnel Страницы: 96

Бренд: Buhler Страницы: 380

Бренд: Amica Страницы: 58

Бренд: Textron Страницы: 182

Бренд: TYM Страницы: 92

Бренд: TYM Страницы: 180

Бренд: TYM Страницы: 204

Бренд: RHINO Страницы: 3

KUBOTA GRAND-L30 Series

Бренд: RHINO Страницы: 4

Бренд: International Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды