Kubota ME8200DTN Скачать руководство пользователя страница 88

Страница: 88 / 192

ME8200DTN, WSM

TRANSMISSION

N3-S24

Disassembling Clutch

1. Remove the internal snap ring (1), and then take out the clutch

discs (2), the pressure plate (6), and the drive plate (7), (8), (9)
and (10).

2. Remove the piston (3) and O-ring (5) by compression air.
3. Remove the parts for other side as above.

(When reassembling)

Install the clutch discs (2) and drive plate (7), (8), (9) and (10)
mutually.

When installing the internal snap ring (1), (19) to the clutch
body, align its split portion to the notched portion clutch body.

Apply enough transmission fluid to the discs (2), (11).

Do not confuse the two types drive plate : The drive plates with
the plug rubbers (20) are (7), (9) and without plug rubbers (20)
are (8) and (10).

Do not confuse the pressure plate (6), (18) and drive plates.
The pressure plate (6), (18) is thicker than the drive plates.

Confirm the moving of the piston (3), (4) smoothly when
pressure air at 0.5 to 1.0 MPa (5 to 10

, 71 to 142 psi)

is sent to clutch pack.

(1)

Internal Snap Ring

(11)

Clutch Disc

(2)

Clutch Disc

(12)

Drive Plate

(3)

Piston

(13)

Drive Plate

(4)

Piston

(14)

Drive Plate

(5)

O-ring

(15)

Drive Plate

(6)

Drive Plate

(16)

Drive Plate

(7)

Drive Plate

(17)

Drive Plate

(8)

Drive Plate

(18)

Drive Plate

(9)

Drive Plate

(19)

Internal Snap Ring

(10)

Drive Plate

(20)

Plug Rubber

0000003483E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды