Kubota ME8200DTN Скачать руководство пользователя страница 49

Страница: 49 / 192

ME8200DTN, WSM

CLUTCH

N2-S4

4. CHECKING, DISASSEMBLING AND SERVICING

[1] TRAVELLING CLUTCH

(1) Checking and Adjusting

Clutch Pedal Free Travel

1. Stop the engine and remove the key.
2. Slightly depress the clutch pedal and measure free travel (L)

at the top of pedal stroke.

3. If adjustment is needed, loosen the lock nut (1), and turn the

turnbuckle (2) to adjust the clutch rod length.

4. Retighten the lock nut (1).

Clutch Pedal Stopper Bolt

1. Measure the height (A) of stopper bolt (2).
2. If the measurement is not within the factory specifications,

adjust it.

3. After adjustment, tighten the lock nut (3) firmly.

(2) Disassembling and Assembling

Foldable ROPS

1. Disconnect the 2P connector from the front combination lamp

(2).

2. Remove the foldable ROPS (1).
3. Remove the ROPS frame right and left (3).

(When reassembling)

Clutch pedal free travel
(L) on the pedal

Factory spec.

35 to 45 mm
1.4 to 1.8 in.

(1)

Lock Nut

(2)

Turnbuckle

0000003618E

Height (A) of clutch
pedal stopper bolt

Factory spec.

18 to 20 mm
0.70 to 0.79 in.

(1)

Clutch Pedal

(3)

Lock Nut

(2)

Stopper Bolt

0000003425E

(A) Separating Engine from Clutch Housing Case

Tightening torque

ROPS frame (L and R)

193.1 to 225.6

20.0 to 23.0

144.7 to 166.4 ft-lbs

Foldable ROPS

29.4 to 49.0

3.0 to 5.0

21.7 to 36.7 ft-lbs

(1)

Foldable ROPS

(3)

ROPS Frame

(2)

Front Combination Lamp

0000003404E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Kubota ME8200DTN, Дополнение к руководству по ремонту, Страница: 49 / 192

Результаты поиска

Содержание ME8200DTN

Отзывы: