Kubota ME8200DTN Скачать руководство пользователя страница 143

Страница: 143 / 192

ME8200DTN, WSM

FRONT AXLE

N6-S16

Clearance between Front Axle Case Bosses and Bracket

Bushings

1. Measure the front axle case bosses O.D. with an outside

micrometer.

2. Measure the bracket bushing I.D. and calculate the clearance.
3. If the clearance exceeds the allowable limit, replace the

bracket bushing.

Press-fitting Bushing

When press-fitting a new bushing, observe the dimension
described in the figure.

After replacing the bushing, be sure to adjust the front
axle pivot. (See page 6-S5.)

Clearance between Bevel Gear Case Boss and Front Axle

Support Bushing

1. Measure the bevel gear case boss O.D. with an outside

micrometer.

2. Measure the support bushing I.D. and calculate the clearance.
3. If the clearance exceeds the allowable limit, replace it.

Clearance between
front axle case boss
(front) and bracket
bushing (front)

Factory spec.

0.025 to 0.160 mm
0.00098 to 0.00630 in.

Allowable limit

0.35 mm
0.0138 in.

Front axle case boss
(front) O.D.

Factory spec.

49.950 to 49.975 mm
1.96653 to 1.96752 in.

Bracket bushing (front)
I.D.

Factory spec.

50.000 to 50.110 mm
1.96850 to 1.97283 in.

Clearance between
front axle case boss
(rear) and bracket
bushing (rear)

Factory spec.

0.025 to 0.190 mm
0.00098 to 0.00748 in.

Allowable limit

0.35 mm
0.0138 in.

Front axle case boss
(rear) O.D.

Factory spec.

70.000 to 70.035 mm
2.75590 to 2.75728 in.

Bracket bushing (rear)
I.D.

Factory spec.

70.060 to 70.190 mm
2.75826 to 2.76338 in.

Press-fit depth of
bushing (A)

Reference value

12.0 to 13.0 mm
0.47 to 0.51 in.

(1)

Bushing

0000003623E

Clearance between
bevel gear case boss
and front axle support
bushing

Factory spec.

0.060 to 0.220 mm
0.00236 to 0.00866 in.

Allowable limit

0.50 mm
0.0197 in.

Bevel gear case boss
O.D.

Factory spec.

54.970 to 55.000 mm
2.16417 to 2.16535 in.

Front axle support
bushing I.D.

Factory spec.

55.060 to 55.190 mm
2.16772 to 2.17283 in.

0000001939E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды