Kubota ME8200DTN Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 192

background image

ME8200DTN, WSM

GENERAL

NG-9

[3] CHECK POINTS OF EVERY 50 HOURS

Checking Engine Start System

A

Do not allow anyone near the tractor while testing.

A

If the tractor does not pass the test, do not operate the
tractor.

B

Preparation before testing.

1. Place all shift lever and hydraulic levers in the "NEUTRAL".
2. Set the parking brake and stop the engine.

B

Test 1 : Switch for the shuttle shift lever.

1. Sit on operator's seat.
2. Shift the shuttle shift lever to the forward or reverse position.
3. Depress the clutch pedal fully.
4. Disengage the PTO clutch control lever.
5. Pull out the engine emergency stop knob and turn the key to

"START" position.

6. The engine must not crank.
7. If it cranks, inspect the safety switch.

B

Test 2 : Switch for the PTO clutch control lever.

1. Sit on operator's seat.
2. Engage the PTO clutch control lever.
3. Depress the clutch pedal fully.
4. Shift the shuttle shift lever to the neutral position.
5. Pull out the engine emergency stop knob and turn the key to

"START" position.

6. The engine must not crank.
7. If it cranks, inspect the safety switch.

Checking Wheel Mounting Nuts Tightening Torque

A

Never operate tractor with a loose rim, wheel, or axle.

A

Any time bolts and nuts are loosened, retighten to
specified torque.

A

Check all bolts and nuts frequently and keep them tight.

1. Check the wheel mounting nuts regularly especially when

new. If there are loosened, tighten as follows.

(1)

Shuttle Shift Lever

(3)

PTO Clutch Lever

(2)

Clutch Pedal

0000003601E

Tightening torque

Front wheel mounting
nut

166.7 to 196.1

17.0 to 20.0

122.9 to 144.6 ft-lbs

Front disc mounting nut

260 to 304

26.5 to 31.0

192 to 224 ft-lbs

Rear wheel mounting
nut and rear disc
mounting nut

260 to 304

26.5 to 31.0

192 to 224 ft-lbs

(1)

Front Wheel Mounting Nut

(3)

Rear Wheel Mounting Nut and

(2)

Front Disc Mounting Nut

Rear Disc Mounting Nut

0000003602E

KiSC issued 04, 2006 A

«
...
20
21
22
23
24
...
»

Содержание ME8200DTN

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ME8200DTN

Бренд: AVANT Страницы: 18

Бренд: Jonsered Страницы: 100

Бренд: Terberg Страницы: 71

Бренд: MAGNATRAC Страницы: 86

Бренд: Sears Страницы: 35

Бренд: Kioti Страницы: 252

GE PROFILETM GCG1500L

Бренд: GE Страницы: 2

Бренд: Webb Страницы: 44

Бренд: Toro Страницы: 44

Бренд: Spearhead Страницы: 54

TWIGA CLASSIC S51

Бренд: Spearhead Страницы: 54

Бренд: Spearhead Страницы: 76

Бренд: Herculano Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды